Z-axis Expansion & CTE

Z-axis Expansion & CTE

Quality & Inspection Standards

PRODUCTS CENTER

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit
Thermal Reliability IPC‑TM‑650 Method 2.4.24

PCB Z‑axis Expansion & CTE – TMA Method, IPC Limits & PTH Reliability

Z‑axis coefficient of thermal expansion (CTE) is the single most important material property for plated through hole (PTH) reliability. When the board heats above Tg, the dielectric expands rapidly in the thickness direction – pulling the copper barrel outward. We have seen 16‑layer backplanes with Z‑axis CTE above Tg of 220 ppm/°C crack after a single lead‑free reflow. By switching to a laminate with CTE above Tg of 80 ppm/°C, the same design survived 10 cycles. Per IPC‑6012E §3.6.2.18, Z‑axis expansion is a critical parameter for Class 3 qualification. This guide covers TMA measurement per IPC‑TM‑650 2.4.24, typical CTE values, and how to specify CTE limits for high‑reliability PCBs.

Published: May 15, 2026  |  10 min read  |  #CTE #ZaxisExpansion #PTHReliability #TMA

1. What Is Z‑axis CTE? – Definition and Units

The coefficient of thermal expansion (CTE) describes how much a material expands per degree of temperature change. For PCB laminates, we care about three directions, but Z‑axis (through‑thickness) is the most critical for reliability because it directly stresses plated through holes and microvias.

  • X‑axis (warp direction): CTE typically 12‑18 ppm/°C (glass‑dominated).
  • Y‑axis (fill direction): CTE typically 12‑18 ppm/°C.
  • Z‑axis (thickness): CTE is resin‑dominated – much higher, especially above Tg.

Two CTE values are reported: α1 (below Tg) and α2 (above Tg). The ratio α2/α1 is typically 3‑5x. CTE is expressed in ppm/°C (parts per million per degree Celsius) or µm/m·°C.

Total Z‑axis expansion (percent): Often expressed as PTE (percent thermal expansion) from 50°C to 260°C. A common Class 3 requirement is PTE <3.5% (some OEMs require <3.0%).

The expansion is anisotropic – FR‑4 expands much more in Z than in X/Y because the glass fibers constrain in‑plane expansion but not thickness.

2. TMA Measurement (IPC‑TM‑650 2.4.24)

IPC‑TM‑650 2.4.24 specifies TMA (thermomechanical analysis) for Z‑axis CTE measurement. Key parameters:

  • Sample: ≈6.35mm × 6.35mm, thickness ≥0.5mm (preferably 1.6mm). Thinner samples can be stacked.
  • Pre‑bake: 105°C for 2 hours to remove moisture.
  • Load: 0.1‑10g (typically 5g) to ensure contact without penetrating the sample.
  • Heating rate: 10°C/min from 35°C to 280°C (or to 300°C for some materials).
  • Measurement: Record thickness change vs temperature. Calculate CTE as slope of the expansion curve: α = (ΔL / L₀) / ΔT.

The method reports:

  • α1 (CTE below Tg): From 50°C to Tg‑10°C (or between two defined points, e.g., 50‑100°C).
  • α2 (CTE above Tg): From Tg+10°C to 260°C (or 250‑280°C).
  • PTE (percent thermal expansion): (Thickness at 260°C – Thickness at 50°C) / Thickness at 50°C × 100.

In our lab, we have seen that sample preparation dramatically affects CTE results. Rough edges or non‑parallel faces cause tilting, which adds measurement error. We require ground surfaces with parallelism within 0.025mm.

Engineering Insight

Always ask for the full TMA expansion curve, not just the CTE numbers. A sudden change in slope below Tg may indicate residual stress or a second phase transition. A smooth, monotonic curve above Tg is ideal – any steps suggest inhomogeneous cure.

3. Typical CTE Values by Material Family

The table below shows typical Z‑axis CTE ranges for common laminate systems (data from IPC‑4101 and supplier datasheets). Values are for after Tg (α2) unless noted.

Material Family α1 (ppm/°C) α2 (ppm/°C) PTE (50‑260°C, %) Typical Application
Standard FR‑4 (Tg 135°C) 50‑60 200‑250 3.5‑4.5% Consumer, single reflow
Mid‑Tg FR‑4 (Tg 155°C) 45‑55 150‑200 2.8‑3.5% Telecom, industrial
High‑Tg FR‑4 (Tg 170°C) 40‑50 100‑150 2.0‑2.8% Server, automotive, HDI
Very high Tg (180‑200°C) 35‑45 80‑120 1.5‑2.2% High‑reliability, multiple reflow
BT / Cyanate ester 30‑40 60‑90 1.0‑1.8% Aerospace, military
Polyimide 25‑35 40‑70 0.8‑1.5% Extreme high temperature

Table 1: Typical Z‑axis CTE ranges. Lower α2 and PTE directly correlate with better PTH reliability. For Class 3 lead‑free, aim for α2 ≤150 ppm/°C and PTE ≤2.5%.

4. Why CTE Matters – PTH Strain & Cracking

When a PCB is heated during reflow (peak 260°C), the Z‑axis expansion stretches the plated copper barrel. Copper has CTE of about 17 ppm/°C – much lower than the dielectric. The differential expansion induces tensile strain in the barrel wall. If the strain exceeds the copper's elongation limit (≥12% per IPC‑6012E), the barrel cracks (Type D cracks).

Simplified strain calculation:

  • Laminate thickness: 1.6mm (1600µm).
  • PTE = 2.5% means the dielectric expands by 40µm in Z‑axis.
  • Copper barrel length is constrained by the dielectric – it must stretch by approximately the same amount.
  • Strain = ΔL / L₀ = 40µm / 1600µm = 0.025 = 2.5%.

A 2.5% strain is well below the 12% elongation of good ductile copper, so why do cracks occur? Because the strain is not uniformly distributed – it concentrates at innerlayer interfaces, at the corner of the pad, and at the edge of the barrel. The effective local strain can be 3‑5x higher than the average. That is why materials with PTE >3.5% almost always crack.

For microvias, the situation is worse: the stubby structure has no barrel to flex, so the entire expansion strain concentrates at the 90° corner between the microvia and the target pad. We have seen microvias crack at PTE as low as 2.0% if the CTE above Tg is >200 ppm/°C. This is why HDI designs require laminates with α2 ≤120 ppm/°C.

Real‑world case: A 10‑layer server board with standard FR‑4 (α2 = 220 ppm/°C, PTE = 3.8%) was qualified at 5 reflow cycles – but failed in the field after 18 months (thermal cycling + power cycles). Autopsy revealed PTH corner cracks. Replacing the core and prepreg with high‑Tg material (α2 = 110 ppm/°C, PTE = 2.0%) eliminated failures. The laminate cost increased 18%, but field returns dropped from 7% to 0.1%.

5. Acceptance Criteria: Class 2 vs Class 3

IPC‑6012E does not specify absolute CTE limits – it references IPC‑4101. However, industry practice has established clear guidelines:

Parameter Class 2 (Typical) Class 3 (Typical) Automotive / HDI IPC‑4101 Slash Sheet
α2 (ppm/°C) – above Tg ≤200 ≤150 ≤120 /124, /126
PTE (50‑260°C) – percent ≤3.5% ≤2.5% ≤2.0% /126, /129
α1 (ppm/°C) – below Tg ≤60 ≤50 ≤45 All
Z‑axis expansion at 260°C (µm/mm) ≤35 ≤25 ≤20 Customer defined

Table 2: Typical CTE acceptance criteria. Always specify numeric limits in your procurement document – do not just say "per IPC."

For HDI with stacked microvias, we impose even stricter limits: α2 ≤100 ppm/°C, PTE ≤1.8%. We have qualified high‑density interconnects with these limits and seen zero microvia corner cracks after 1000 thermal cycles.

Z‑axis CTE Specification Checklist (IPC‑Anchored)

  1. Specify α2 (above Tg) and PTE. Example: "α2 ≤150 ppm/°C, PTE ≤2.5% from 50°C to 260°C."
  2. Require TMA per IPC‑TM‑650 2.4.24, 10°C/min ramp, 5g load. Specify the temperature range (e.g., 50‑260°C).
  3. Ask for the full expansion curve. Not just α1 and α2 – examine slope changes and any steps that indicate poor cure.
  4. For HDI, add α2 ≤120 ppm/°C and PTE ≤2.0%. Stacked microvias demand lower CTE to avoid corner cracks.
  5. Verify that the supplier reports α2 from Tg+10°C to 260°C. Some suppliers use 250°C as the upper limit – this understates expansion.
  6. Correlate CTE with thermal stress microsection. If CTE is borderline, require additional PTH thermal stress testing per IPC‑TM‑650 2.4.13.1.
  7. For thick boards (>3.2mm), specify maximum PTE to prevent barrel cracking during wave solder. Thick boards experience higher absolute expansion.

6. FAQ

Q: What is a good Z‑axis CTE value for lead‑free assembly?

A: For single lead‑free reflow, α2 ≤150 ppm/°C and PTE ≤2.5% are generally safe. For multiple reflows (3‑5 cycles), aim for α2 ≤120 ppm/°C and PTE ≤2.0%. For very high‑reliability (aerospace, automotive), α2 ≤100 ppm/°C and PTE ≤1.8% are recommended.

Q: Does lower CTE always mean better reliability?

A: Generally yes for Z‑axis, but extremely low CTE materials (e.g., polyimide) are more expensive and harder to process (drill, plasma etch). The cost increase may not be justified for low‑cycle applications. Always trade off.

Q: How does moisture affect Z‑axis CTE?

A: Moisture plasticizes the resin, lowering Tg and increasing α2. A wet board (moisture >0.2%) can have CTE 20‑30% higher than a dry board. This is why pre‑baking is required before TMA testing. For production, control moisture via dry cabinets and vacuum baking before reflow.

Q: What is the maximum PTE allowed by IPC‑6012E for Class 3?

A: IPC‑6012E does not specify a maximum PTE number. It defers to IPC‑4101 and the customer. However, most Class 3 specifications require PTE ≤2.5% (50‑260°C). Some OEMs (e.g., major server companies) require ≤2.0% for high‑density designs.

Concerned about Z‑axis expansion and PTH cracking in your high‑reliability design? Our engineers will review your stackup, recommend CTE limits, and run thermal stress simulation to ensure PTH reliability.

Request CTE & PTH Reliability Review →

References: IPC‑TM‑650 2.4.24; IPC‑6012E §3.6.2.18; IPC‑4101 (slash sheets /124, /126, /129); IPC‑2221B. IPC‑TM‑650 Official Method.

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit