Reflow Simulation Testing

Reflow Simulation Testing

Quality & Inspection Standards

PRODUCTS CENTER

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit
Thermal Reliability IPC‑TM‑650 Method 2.6.27

Reflow Simulation Testing – IPC‑TM‑650 2.6.27, HDI Reliability & Multiple Reflow Effects

Reflow simulation is not the same as solder float. While 288°C solder float tests peak temperature tolerance, reflow simulation (IPC‑TM‑650 2.6.27) replicates the entire thermal profile of lead‑free assembly: ramp, soak, peak, and cool. This matters because modern PCBs see multiple reflow passes – sometimes five or more for complex HDI builds. We have seen boards that survived a single solder float but delaminated after the third reflow simulation cycle. The gradual stress accumulation from repeated heating and cooling is not captured by a single peak‑temperature test. Per IPC‑6012E §3.6.2.19, convection reflow simulation is the preferred method for evaluating assembly‑related thermal stress. This guide covers the 2.6.27 method, typical reflow profiles, failure modes unique to multiple reflows, and acceptance criteria for Class 2 vs Class 3.

Published: May 15, 2026  |  10 min read  |  #ReflowSimulation #MultipleReflow #HDIReliability

1. Why Reflow Simulation – Beyond Solder Float

Solder float (IPC‑TM‑650 2.4.13.1) is a pass/fail test for gross thermal integrity. It applies a severe 288°C shock for 10 seconds. But it does not replicate real assembly conditions. Lead‑free reflow has a ramp rate of 1‑3°C/s, a soak at 150‑200°C for 60‑120 seconds, then a peak of 245‑260°C for 30‑90 seconds – much longer at lower peak temperatures than solder float. The extended time at elevated temperature stresses laminates differently.

Key differences:

  • Solder float: Harsh peak, short duration. Catches brittle defects (plating voids, gross delamination).
  • Reflow simulation: Lower peak, longer dwell. Catches fatigue and cumulative damage (microvia corner cracks, progressive delamination, CAF initiation).

In an HDI program for a 0.8mm pitch FPGA, the board passed single solder float but failed after 3 reflow simulation cycles. Microsection revealed microvia target pad separation that was not present after solder float. The root cause was CTE mismatch; the repeated heating allowed fatigue cracks to propagate. The supplier requalified with a higher‑Tg laminate, and the board survived 10 cycles. Reflow simulation catches what solder float misses.

2. Test Method IPC‑TM‑650 2.6.27 – Profile, Equipment & Setup

IPC‑TM‑650 2.6.27 specifies convection reflow simulation. The test uses a forced‑air reflow oven capable of profiling to a defined temperature curve. Key parameters:

  • Sample: Finished PCB or test coupon with PTHs and microvias. No components – bare board.
  • Pre‑conditioning: Bake at 125°C for 24 hours to remove moisture (optional but recommended).
  • Profile: Typically follows J‑STD‑020 or customer‑defined profile for lead‑free assembly.
  • Number of cycles: Defined by customer. Common values: 3, 5, 10, or 30 cycles.

A typical lead‑free reflow profile (SAC305):

  • Ramp to 150°C at 1‑3°C/s
  • Soak at 150‑200°C for 60‑120 seconds
  • Ramp to peak (245‑260°C) at 1‑3°C/s
  • Time above liquidus (217°C): 30‑90 seconds
  • Cool to 150°C at 2‑4°C/s

The board is placed in the oven, and a thermocouple is attached to the board surface to verify the profile. After the specified number of cycles, the board is microsectioned and inspected for delamination, cracks, and separation.

Important: The oven must be calibrated per the manufacturer's instructions, and the profile must be verified on a representative board (not empty oven). We have seen labs run empty‑oven profiles, then test boards – the board's thermal mass changes the actual profile, leading to under‑stress or over‑stress.

3. Typical Reflow Profiles: SAC305, SnPb, and Low‑Temp Solder

The choice of reflow profile affects the stress seen by the board. Below are common profiles per J‑STD‑020 and IPC‑7530.

Solder Type Peak Temp (°C) Time Above Liquidus (s) Typical Cycles Application
SAC305 (lead‑free) 245‑260 60‑90 3‑5 (up to 30 for HDI) Standard lead‑free assembly
Sn63/Pb37 (tin‑lead)   215‑225 40‑70 3‑5 Legacy / military (exempt)
Low‑temp (SnBi) 160‑180 60‑90 3‑5

Table 1: Common reflow profiles. For HDI and high‑reliability, use SAC305 profile with 5 cycles minimum.

Multiple reflow cycles matter. An HDI board may see: top‑side reflow, bottom‑side reflow, rework, and two reflow passes for a PoP (package‑on‑package). That can total 5‑6 cycles. We have seen microvia corner cracks initiate at cycle 2 and propagate fully by cycle 5. Specifying "3 cycles" may pass but 5 cycles may fail – define based on your actual assembly process.

4. Failure Modes Unique to Multiple Reflow Simulation

Multiple reflow cycles cause progressive damage that is not seen in single‑pass tests:

  • Microvia target pad separation: CTE mismatch causes the microvia to lift from the target pad. In one study, 25% of microvias showed separation after 5 cycles, compared to 0% after 1 cycle. The mechanism is fatigue – each cycle adds strain until the interface fails.
  • Progressive delamination: Delamination that starts at the board edge or near a via expands with each cycle. We have seen 1mm² delamination after 2 cycles grow to 5mm² after 5 cycles.
  • Copper fatigue cracking (Type D propagation): A Type B crack at the innerlayer may not be through the wall after 1 cycle but becomes Type D after 3‑5 cycles. This is why Class 3 often requires 5‑cycle reflow simulation.
  • Resin decomposition (brown charring): Low‑Td materials (<320°C) may show discoloration after multiple cycles. This indicates permanent degradation – the board is losing mechanical strength.

In an automotive radar program, the customer required 30 reflow cycles (simulating multiple assembly and rework steps). Standard FR‑4 failed after 8 cycles – massive delamination. Switching to a high‑Tg, high‑Td material (Tg 180°C, Td 360°C) allowed the board to survive all 30 cycles without visible degradation. The lesson: match the test severity to your actual process, not just IPC minimums.

5. Acceptance Criteria: Class 2 vs Class 3

IPC‑6012E does not provide a separate table for reflow simulation acceptance – it uses the same criteria as thermal stress (288°C solder float). However, industry practice has established tighter limits for multiple‑cycle reflow simulation, especially for HDI.

Defect Class 2 (3 cycles) Class 3 (5 cycles) HDI / High‑Cycle (10+ cycles) IPC Reference
Microvia target pad separation ≤10% of via diameter Zero separation Zero separation IPC‑6018 §5.2
Delamination ≤1% board area per side Zero tolerance Zero tolerance IPC‑6012E §3.2.3
Type D copper crack Accept if remaining Cu ≥18µm Zero tolerance Zero tolerance IPC‑6012E §3.6.2.1
Resin char / discoloration Accept if no structural loss No discoloration No discoloration AABUS (customer spec)
Measling (white spots) Accept if no bridging Accept only limited Process warning – investigate IPC‑6012E §3.2.3

Table 2: Acceptance after reflow simulation. For Class 3, zero microvia separation and zero delamination are mandatory.

Many OEMs require 5 cycles as the baseline for Class 3. For HDI with stacked microvias, we have seen requirements as high as 10‑30 cycles. Always specify the number of cycles and the acceptance criteria in your purchase order. Do not assume "per IPC" covers multiple reflows.

Reflow Simulation Test Checklist (IPC‑Anchored)

  1. Specify the reflow profile in your PO. Example: "Reflow simulation per IPC‑TM‑650 2.6.27, SAC305 profile, peak 250±5°C, 5 cycles."
  2. Require profile verification with a thermocouple attached to a sample board. An empty‑oven calibration is not sufficient.
  3. Define the number of cycles based on your assembly process. For typical lead‑free, 3‑5 cycles. For HDI with PoP, 7‑10 cycles. For high‑rework products, up to 30 cycles.
  4. Include daisy‑chain coupons for resistance monitoring. A 10% resistance increase during cycling is a failure.
  5. After cycling, perform microsection at 200‑500x. Focus on microvias, innerlayer interfaces, and PTH barrels.
  6. Check for progressive damage. Compare as‑polished and post‑cycling microsections. New cracks or expanded separation are rejectable for Class 3.
  7. Document all failures with 200‑500x micrographs. Include cycle count at failure if resistance monitoring was used.

6. FAQ

Q: What is the difference between reflow simulation (2.6.27) and solder float (2.4.13.1)?

A: Solder float applies 288°C for 10 seconds – a harsh peak but short duration. Reflow simulation applies a realistic assembly profile (ramp, soak, peak at 245‑260°C, cool). Reflow simulation is better for detecting fatigue and cumulative damage from multiple thermal cycles. Solder float is better for detecting brittle defects.

Q: How many reflow cycles should I specify for Class 3?

A: The IPC default is not specified. Industry practice: 5 cycles for standard Class 3, 10 cycles for HDI, and up to 30 cycles for high‑reliability medical or aerospace. Base it on your expected assembly steps: top reflow + bottom reflow + potential rework + PoP assembly.

Q: Can I use reflow simulation on assembled boards?

A: The method is defined for bare boards. Running an assembled board through reflow simulation will melt solder joints and may damage components. Use dedicated test coupons on the same panel.

Q: What is the most common failure in multi‑cycle reflow simulation?

A: Microvia target pad separation, especially in stacked microvia designs. The repeated expansion and contraction fatigue the copper‑copper interface. If you have any microvias, specify 5‑cycle reflow simulation and examine at 500x.

Need help defining reflow simulation requirements for your HDI or high‑reliability design? Our engineers will review your assembly process and recommend the appropriate number of cycles and acceptance criteria per IPC‑TM‑650 and IPC‑6012.

Request Reflow Simulation Test Plan →

References: IPC‑TM‑650 2.6.27; IPC‑6012E §3.6.2.19; IPC‑6018 §5.2; IPC‑A‑600J §3.3.9; J‑STD‑020 (reflow profiles). IPC‑TM‑650 Official Method.

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit