Advanced PCB & PCBA Product Center
Explore RF, microwave, high-frequency, high-speed, HDI, rigid-flex, flexible, Rogers, heavy copper and multilayer PCB products, supported by assembly and sourcing from prototype through production.
2–128 Layer PCB Capability
RF, Microwave, High-Speed & HDI
IPC Class 2 & Class 3 Build Support
AOI, Electrical Test & Final Inspection
Explore PCB Products & Services
Showing all results
Showing of results
10-Layer 2nd-Order HDI Rigid-Flex PCB with Laser Microvias
Structure: 10L Rigid-Flex · Dual PI Flex Cores HDI: 2nd-Order · 4 mil Laser Microvias Technology: Fine-Pitch Routing · Resin-Plugged Vias
8-Layer Rigid-Flex PCB with 2-Layer PI Flex Core
Structure: 8L Rigid · 2L PI Flex Features: Dual Rigid Sections · Dense Pad Layouts Engineering: Regional Stackup · Flex Transition DFM
6-Layer Multi-Zone Rigid-Flex PCB with Dual PI Flex Cores
Structure: 6L Rigid · Dual PI Flex Cores Routing: Multi-Zone · L2–L5 Flex Layers Focus: Dense I/O · Stackup DFM
10-Layer Rigid-Flex PCB with Resin-Plugged Vias
Structure: 10L Rigid · 2L PI Flex Core Via Process: Mechanical PTH · Resin Plugging Engineering: Connector DFM · Regional Stackup
4-Layer Multi-Connector Rigid-Flex PCB with PI Flex Core
Structure: 4L Rigid · 2L PI Flex (L2/L3) Layout: Multi-Branch Connector Interfaces Engineering: Copper-Balance & Transition DFM
8-Layer Rigid-Flex PCB with Dual PI Flex Cores
Structure: 8L Rigid · Dual PI Flex Cores Flex Layers: L2/L3 + L6/L7 Features: Multi-Region Routing · ENIG
4-Layer Rigid-Flex PCB with FR-4 Stiffeners
Structure: 4L Rigid · 2L PI Flex Core Construction: FR-4 Stiffeners · Regional Thickness Engineering: Rigid–Flex Transition DFM
8-Layer Panelized Rigid-Flex PCB for Multi-Connector Modules
Structure: 8L Rigid · 2L PI Flex (L4/L5) Configuration: Repeated Connector Array Engineering: Panel Rails · Transition DFM
Featured PCB & PCBA Case Studies
16-Layer Any-Layer HDI PCB
A 16-layer Any-Layer HDI architecture used stacked microvias and fine-line routing to reduce board area by 30% for a compact implantable medical device.
Read Case Study
40% Better Cooling for 800V EV Power Modules with Embedded Copper & Heavy Copper
Overheating threatened reliability. We embedded copper busbars and applied selective heavy copper—transforming the PCB into an active power path, cutting peak temperature by 40% for safe continuous operation.
Read Case Study
24/7 Reliability for Smart City Surveillance with High‑Tg & Blind/Buried Via
Intermittent failures after thermal cycling? We used high‑Tg/low‑CTE materials, blind/buried vias, and thick gold plating—eliminating via fatigue for continuous outdoor operation.
Read Case Study
Copper Inlay & Hybrid Lamination for High‑Power Robotics Thermal Management
A 120A servo drive overheated under continuous load. We embedded copper inlays for direct heat paths and used hybrid lamination to separate power from signal—achieving stable operation without bulky cooling.
Read Case Study
Solving Rigid‑Flex Failure in High‑Vibration Aerospace Systems
Intermittent signal drops and thermal cycling failures traced to rigid‑flex transitions. We smoothed the transition, rebalanced the 14‑layer stack‑up, and tightened process controls—eliminating failure under vibration.
Read Case Study
224Gbps AI Server PCB: From Signal Collapse to Stable Channel
Closed eye diagram and excessive loss at 224Gbps? We redesigned the channel, switched to Megtron 7, and applied sub‑8mil backdrilling—recovering a clean eye diagram and stable transmission.
Read Case Study
PCB Product Selection & Quotation FAQ
What files are needed to quote a microwave PCB with controlled impedance?
Gerber/ODB++, target impedance list, stack-up intent (or constraints), coupon requirements, and any critical RF routing notes.
Do you support “thin copper” or local copper optimization for sharper RF corners?
It can be supported when the design requires it; local thin-copper processing may improve corner accuracy versus full-board copper tolerance control.
Do you have real RF performance validation data?
Yes. The microwave filter bandwidth target is 5.7–7.0GHz; measured test is 5.86–7.19GHz, matching within <5% deviation.
What impedance tolerance can you support for this build?
This design targets ±5% impedance tolerance with verification and process locking for consistency.
Why use resin-filled vias on high-frequency microwave boards?
Resin-filled vias improve surface planarity and reduce solder wicking/void-related risk, supporting reliable RF assembly.
Our Manufacturing Capabilities
Core PCB and PCBA technologies supporting RF, high-speed, HDI, flex, power electronics and complex multilayer projects.
Submit Your PCB or PCBA Project for Engineering Review
Upload your Gerber or ODB++, fabrication drawing, stackup, BOM and project requirements. Our engineering team will review the manufacturing scope, technical risks and quotation requirements.


