PCB Glass Transition Temperature (Tg)

PCB Glass Transition Temperature (Tg)

Quality & Inspection Standards

PRODUCTS CENTER

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit
Thermal Reliability IPC‑TM‑650 Methods 2.4.24 / 2.4.25

PCB Glass Transition Temperature (Tg) – DSC vs TMA, Material Selection & IPC Requirements

Glass transition temperature (Tg) is not just a number on a datasheet – it is the single most important indicator of a laminate's thermal and mechanical limits. Below Tg, the resin is rigid and glassy. Above Tg, it becomes rubbery, with Z‑axis expansion increasing 3‑5x. We have seen server boards with Tg 140°C delaminate after three lead‑free reflows, while Tg 170°C boards from the same stackup survived 10 cycles. Per IPC‑4101, Tg is a mandatory property for all laminate types. This guide covers test methods (DSC vs TMA), typical Tg ranges for common materials, and how to specify Tg for Class 2 vs Class 3 applications.

Published: May 15, 2026  |  11 min read  |  #Tg #GlassTransition #MaterialSelection

1. What Is Tg? – Physics of the Glass Transition

Glass transition temperature is the temperature range where an amorphous polymer (epoxy, polyimide, etc.) changes from a hard, glassy state to a soft, rubbery state. It is not a melting point – the material does not liquefy. Instead, molecular chains gain mobility, causing dramatic changes in:

  • Thermal expansion coefficient (CTE): Below Tg, CTE is typically 15‑35 ppm/°C. Above Tg, it jumps to 50‑250 ppm/°C (Z‑axis).
  • Mechanical strength: Flexural and peel strength drop significantly above Tg.
  • Chemical resistance: Solvents penetrate faster above Tg.

Per IPC‑4101, Tg is defined as the inflection point (midpoint) of the thermal expansion curve measured by TMA or the heat flow curve measured by DSC. The reported Tg value depends heavily on the test method.

2. Test Methods: DSC vs TMA – Why They Give Different Numbers

Two methods are commonly used to measure Tg, and they do not produce the same result. IPC‑4101 allows both but requires the method to be stated.

Method What It Measures Typical Tg Difference IPC Reference
DSC (2.4.25) Change in heat capacity (endothermic shift) Baseline (reference) IPC‑TM‑650 2.4.25
TMA (2.4.24) Change in coefficient of thermal expansion (slope change) Typically 3‑8°C lower than DSC IPC‑TM‑650 2.4.24

In practice, a material rated at 170°C by DSC often measures 162‑165°C by TMA. Do not compare Tg values measured by different methods. Always specify the test method in your material callout.

DSC method details (2.4.25): Sample 10‑40mg, sealed in aluminum pan, heated at 20°C/min from below Tg to above Tg. The midpoint of the heat flow step is reported as Tg. A second scan (re‑heat) gives the "post‑cure" Tg – if ΔTg >5°C, the material was under‑cured.

TMA method details (2.4.24): Sample ≈6.35mm square, 0.5‑1.6mm thick, heated at 10°C/min with 5g load. The intersection of two tangent lines drawn on the expansion curve defines Tg. TMA also provides CTE below and above Tg.

Engineering Insight

We have seen multiple suppliers inflate Tg by using DSC and reporting the onset temperature instead of the midpoint. Always ask for the full DSC curve and confirm the inflection method. For Class 3, we require TMA verification on first article.

3. Typical Tg Ranges by Material Family

The table below shows typical DSC Tg ranges for common laminate systems. Verify with your supplier's datasheet.

Material Family Typical Tg (°C, DSC) Application IPC‑4101 Slash Sheet
Standard FR‑4 (low Tg) 130‑140 Consumer, single reflow /21, /24
Mid‑Tg FR‑4 150‑165 Industrial, telecom /26, /27
High‑Tg FR‑4 (lead‑free) 170‑180 Server, automotive, multiple reflow /124, /126
Very high Tg (modified epoxy) 180‑200 High‑reliability, HDI /128, /129
BT / Cyanate ester 190‑220 Aerospace, military /101, /102
Polyimide 230‑280 Extreme high temperature /41, /42
PTFE / hydrocarbon (RF) N/A (semicrystalline, no clear Tg) High frequency IPC‑4103

Table 1: Typical DSC Tg ranges. For PTFE and some RF materials, glass transition is not well‑defined – use TMA expansion curves instead.

4. Why Tg Matters – Z‑axis Expansion & PTH Reliability

The most critical reliability impact of Tg is on Z‑axis thermal expansion. When the board heats above Tg, the dielectric expands rapidly, pulling the PTH barrel outward. This causes:

  • Copper barrel cracking (Type D): If the CTE above Tg exceeds 100 ppm/°C (common for low‑Tg FR‑4), a single reflow can crack plated through holes.
  • Innerlayer separation (pink ring): Differential expansion between copper (17 ppm/°C) and resin (>100 ppm/°C) shears the oxide interface.
  • Microvia corner cracks: Even more severe because microvias have no barrel to flex – stress concentrates at the 90° corner.

Numerical example (per IPC‑TM‑650 2.4.24):

  • Laminate Tg 140°C, CTE below Tg = 50 ppm/°C, CTE above Tg = 160 ppm/°C.
  • Heated from 25°C to 260°C (peak reflow). Below Tg: 115°C ΔT × 50 ppm = 5750 ppm (0.58%). Above Tg: 120°C ΔT × 160 ppm = 19200 ppm (1.92%).
  • Total Z‑axis expansion = 2.5%. A 1.6mm thick board expands 40µm in Z‑axis, putting enormous strain on PTHs.

For a high‑Tg material (170°C), the time spent above Tg is shorter, and the CTE above Tg is often lower (e.g., 80‑120 ppm/°C). Total expansion can be <1.5%. This is why Class 3 and automotive PCBs specify Tg ≥170°C.

We have evaluated two identical 12‑layer boards with different laminate: one with Tg 140°C, one with Tg 170°C. After 5 lead‑free reflow cycles, the low‑Tg board showed 22% of PTHs with Type D cracks. The high‑Tg board had zero cracks. The material cost difference was 12% – the field failure cost would have been 50x higher.

5. How to Select Tg for Your Application (Class 2 vs Class 3)

IPC‑6012E does not mandate a specific Tg value – it is defined by the material specification (IPC‑4101) and customer requirements. However, industry practice recommends:

Application Recommended Tg (DSC) Typical Laminate Type Rationale
Class 2 (consumer, basic industrial) ≥130°C Standard FR‑4 Single reflow, low thermal stress
Class 3 (telecom, server, medical) ≥170°C High‑Tg FR‑4 Multiple lead‑free reflows, Z‑axis control
Automotive under‑hood ≥170°C (often 180°C+) High‑Tg with CAF resistance High temperature cycling
Aerospace / military ≥200°C Polyimide, BT, cyanate ester Extreme temperature, long life
HDI / stacked microvias ≥170°C (prefer 180°C+) High‑Tg, low‑CTE above Tg Microvia corner crack prevention

Table 2: Tg selection guide. Higher Tg increases cost and may reduce other properties (e.g., Dk stability). Always trade off.

Cost tradeoff: Moving from Tg 140°C to 170°C typically adds 10‑15% to laminate cost. Moving to polyimide (Tg 260°C) adds 100‑200%. For many Class 2 products, the higher Tg is unnecessary. We have seen teams over‑specify Tg 180°C for a simple single‑reflow board – wasting money without reliability benefit.

Tg Specification Checklist (IPC‑Anchored)

  1. Specify the IPC‑4101 slash sheet. Example: "Laminate per IPC‑4101/126 (Tg ≥170°C by DSC)."
  2. State the test method. "Tg measured by DSC per IPC‑TM‑650 2.4.25, midpoint method."
  3. Request full DSC curves for qualification. Not just a single number – verify the inflection and the absence of a second Tg (which indicates partial cure).
  4. For Class 3, request TMA verification. TMA better reflects in‑board thermal expansion behavior.
  5. Check ΔTg (cure factor). Per IPC‑TM‑650 2.4.25, a second heat Tg more than 5°C higher than the first indicates under‑cure.
  6. Specify CTE below and above Tg. Especially for HDI and thick boards. CTE above Tg should be ≤150 ppm/°C for lead‑free reliability.
  7. Do not compare Tg across different suppliers without verifying method. One supplier's "180°C" may be another's "165°C" if methods differ.

6. FAQ

Q: What is the difference between Tg by DSC and TMA?

A: DSC measures heat flow change; TMA measures expansion change. TMA Tg is typically 3‑8°C lower. Always compare only within the same method. IPC‑4101 allows both but requires the method to be stated.

Q: Is higher Tg always better?

A: Not necessarily. Very high Tg materials (polyimide, cyanate ester) are more expensive, harder to drill, and may have higher moisture absorption. Specify only what your thermal profile requires. For a single reflow, Tg 150°C may be sufficient.

Q: Can a material have two Tg values?

A: Yes – blends of different resins (e.g., epoxy + PPO) can show two distinct glass transitions. This is not necessarily a defect, but it complicates reliability prediction. IPC‑4101 allows two‑phase systems but requires both Tg values to be reported.

Q: Does IPC‑6012E require a specific Tg for Class 3?

A: No. IPC‑6012E defers to the laminate specification (IPC‑4101) and customer requirements. However, most Class 3 programs require Tg ≥170°C (DSC) to survive multiple lead‑free reflows. Always confirm with your customer.

Not sure which Tg your PCB needs? Our engineers will review your assembly profile and recommend the optimal laminate per IPC‑4101 and IPC‑6012.

Request Material Selection Review →

References: IPC‑TM‑650 2.4.24 (TMA), 2.4.25 (DSC); IPC‑4101 (laminate specification); IPC‑6012E §3.6.2.18; IPC‑2221B. IPC‑TM‑650 Official Method.

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit