Rework Reliability
Quality & Inspection Standards
PRODUCTS CENTER
Get Custom Quote
PRODUCTS CENTER
Rework Reliability Evaluation Using IPC‑TM‑650 – Dye & Pry, Microsection, Thermal Shock & Solder Ball Pull Test Methods
Rework operations subject printed circuit board assemblies to additional thermal stress that can degrade solder joint integrity, intermetallic compound (IMC) morphology, pad adhesion, and laminate structure. This engineering framework from UltroNiu describes how to use standardized IPC‑TM‑650 test methods to quantitatively evaluate the effects of rework on reliability. The methods covered include Dye & Pry (2.4.57.2), Microsection (2.1.1), Thermal Shock (2.6.7 or 2.6.7.2), C‑SAM (2.6.21), and Solder Ball Pull / Shear (which, while not in TM‑650, is included as an industry reference). Acceptance criteria are not specified in IPC‑TM‑650; users must establish pass/fail limits based on their product reliability requirements.
Table of Contents
- Scope – What IPC‑TM‑650 Provides for Rework Evaluation
- Rework‑Induced Failure Mechanisms & Corresponding TM‑650 Methods
- Dye & Pry (IPC‑TM‑650 2.4.57.2) – Detecting Cracks in Solder Joints
- Microsection (IPC‑TM‑650 2.1.1) – IMC Thickness, Voiding & Pad Lifting
- Thermal Shock (IPC‑TM‑650 2.6.7 / 2.6.7.2) – Accelerated Life of Reworked Joints
- C‑SAM (IPC‑TM‑650 2.6.21) – Laminate Delamination Detection
- Solder Ball Pull / Shear – Mechanical Strength (Industry Reference)
- Test Coupon Design for Rework Simulation
- Sampling & Documentation
- FAQ
- Rework Reliability Test Checklist
1. Scope – What IPC‑TM‑650 Provides for Rework Evaluation
IPC‑TM‑650 is a collection of test methods for printed board materials and interconnections. It does not specify:
- Maximum allowable number of rework cycles
- Acceptable IMC thickness limits
- Pass/fail criteria for dye & pry or voiding
- Rework process parameters (temperature, time, flux type)
Instead, IPC‑TM‑650 provides standardized test procedures to generate quantitative data on the condition of reworked assemblies. Users then compare this data against internally defined reliability requirements or customer specifications. This framework describes how to apply the relevant TM‑650 methods to evaluate rework effects.
2. Rework‑Induced Failure Mechanisms & Corresponding IPC‑TM‑650 Test Methods
| Potential Damage from Rework | IPC‑TM‑650 Test Method | Measurable Output |
|---|---|---|
| Cracks at BGA/solder interface (hidden) | 2.4.57.2 Dye & Pry | Dye penetration indicates cracks |
| Excessive IMC growth (Cu₃Sn, Cu₆Sn₅, Ni₃Sn₄) | 2.1.1 Microsection + optional SEM | IMC layer thickness (µm) |
| Voiding in solder joints | 2.1.1 Microsection (or X‑ray per 2.4.52) | Void area percentage |
| Pad lifting / copper peel | 2.1.1 Microsection, also 2.4.8 Peel Strength | Separation evidence, peel force (N/mm) |
| Laminate delamination | 2.6.21 C‑SAM (Scanning Acoustic Microscopy) | Delamination area / depth |
| Reduced mechanical strength | Industry method: solder ball pull / shear | Force to failure (gf or N) |
| Thermal cycle life degradation | 2.6.7 (or 2.6.7.2) Thermal Shock | Resistance change, cycles to failure |
3. Dye & Pry (IPC‑TM‑650 2.4.57.2) – Detecting Cracks in Solder Joints
This destructive test method is used to reveal cracks at the interface between solder and component pad, particularly under BGAs and other area‑array packages. Rework can introduce micro‑cracks that are not visible by X‑ray or optical inspection.
- Procedure summary: A low‑viscosity dye penetrant is applied to the component edge, then the component is mechanically pried off. Dye penetrates any cracks, staining the fractured surfaces.
- Application to rework: Perform dye & pry on sample boards after 1, 2, or 3 rework cycles to determine at which cycle cracks first appear.
- Output: Percentage of solder balls showing dye penetration, and fracture mode (ductile vs brittle).
IPC‑TM‑650 2.4.57.2 does not define a pass/fail criterion; users must set internal limits (e.g., 0% dye penetration for Class 3).
4. Microsection (IPC‑TM‑650 2.1.1) – IMC Thickness, Voiding & Pad Lifting
Microsectioning is the primary method to evaluate internal solder joint structures after rework. It provides quantitative data on:
- IMC thickness: Measure the intermetallic layer between solder and pad. Excessive IMC (typically >5 µm for SAC) indicates embrittlement risk.
- Voiding: Voids in BGA balls or through‑hole fillets can be measured as a percentage of joint area.
- Pad lifting / copper peel: Detect separation of copper from laminate or nickel from copper.
For rework evaluation, prepare microsections from samples subjected to different rework counts. Compare IMC thickness and voiding trends. Record data in a structured table.
5. Thermal Shock (IPC‑TM‑650 2.6.7 / 2.6.7.2) – Accelerated Life of Reworked Joints
Thermal shock testing accelerates the fatigue of solder joints caused by coefficient of thermal expansion (CTE) mismatch. It is useful to compare the relative reliability of non‑reworked vs reworked assemblies.
- Typical conditions: -40°C to +125°C, 15‑30 minute dwells, 500 or 1000 cycles.
- Monitoring: Daisy‑chain circuits are used to detect electrical opens. Resistance increase >20% indicates failure.
- Application: Test coupons with and without rework to quantify the reduction in thermal cycle life due to rework.
IPC‑TM‑650 2.6.7 provides the test method; cycle limits are product‑specific.
6. C‑SAM (IPC‑TM‑650 2.6.21) – Laminate Delamination Detection
Repeated thermal exposure from rework can cause internal delamination of the PCB laminate, especially in moisture‑sensitive boards. C‑SAM (Scanning Acoustic Microscopy) non‑destructively detects delaminations.
- Output: Acoustic images showing delamination area and depth.
- Application: Scan boards before and after rework to detect new or enlarged delaminations.
7. Solder Ball Pull / Shear – Mechanical Strength (Industry Reference)
While not part of IPC‑TM‑650, solder ball pull and shear testing is widely used to measure mechanical strength degradation after rework. This framework includes it as a complementary method.
- Typical procedure: A pull tool (or shear tool) applies force to a soldered ball or passive component until failure.
- Data: Record peak force (gf or N) and failure mode (ductile, brittle, pad lift).
- Rework evaluation: Compare pull/shear strength of reworked joints to non‑reworked baseline. Significant reduction indicates damage.
Users should define acceptable strength retention (e.g., ≥80% of baseline) based on their reliability goals.
8. Test Coupon Design for Rework Simulation
To evaluate rework effects using IPC‑TM‑650 methods, the following test structures SHALL be included on a dedicated coupon:
- BGA land pattern (0.8 mm and 0.5 mm pitch): For dye & pry (2.4.57.2) and microsection (2.1.1).
- Surface mount pads (0603, 0402): For solder ball pull / shear testing.
- Large copper pads (2×2 mm): For peel strength (2.4.8) if needed.
- Daisy‑chain circuit: For thermal shock monitoring (2.6.7).
- Solid copper plane area: For C‑SAM baseline.
Simulate rework using the intended rework profile (hot air, IR, etc.) on separate coupons for 0, 1, 2, and 3 rework cycles. Then apply the relevant TM‑650 tests to each group.
9. Sampling & Documentation for Rework Reliability Testing
- Qualification sample size: Test 5 coupons per rework cycle condition (0, 1, 2, 3 cycles).
- For dye & pry: At least 2 coupons per condition.
- For microsection: Prepare 2 cross‑sections per condition (3‑5 joints per section).
- For thermal shock: 1 daisy‑chain coupon per condition (or more for statistical significance).
- Documentation: Record all TM‑650 test parameters (e.g., temperature, dwell time, ramp rate). Report raw data (IMC thickness, void %, pull force, cycles to failure) without applying acceptance criteria.
10. FAQ – Rework Reliability Testing with IPC‑TM‑650
Q: Does IPC‑TM‑650 specify how many rework cycles are allowed?
A: No. IPC‑TM‑650 provides only test methods. The maximum number of rework cycles must be defined by the user based on product reliability requirements, customer specifications, or industry standards such as IPC‑7711/7721 (which are separate documents).
Q: What is the best IPC‑TM‑650 method to detect hidden cracks after rework?
A: Dye & Pry (2.4.57.2) is the most sensitive method. It reveals even micro‑cracks at the interface that are invisible to X‑ray or optical inspection.
Q: Can I use IPC‑TM‑650 2.1.1 to measure IMC on reworked boards?
A: Yes. Prepare microsections per 2.1.1 and use a metallurgical microscope or SEM with EDS to measure IMC thickness. IPC‑TM‑650 does not set a limit; you must compare to baseline.
Q: Does IPC‑TM‑650 include a method for solder ball pull?
A: No. Solder ball pull and shear are industry methods (e.g., JESD22‑B117A). They are mentioned here as complementary tools but are not part of IPC‑TM‑650.
Rework Reliability Test Checklist (IPC‑TM‑650 Focus)
- 1. Test coupon designed with BGA pads, passive pads, daisy‑chain, and C‑SAM reference area.
- 2. Rework profile recorded (peak temperature, dwell time, ramp rate).
- 3. Samples prepared for 0, 1, 2, and 3 rework cycles (minimum 5 coupons per condition).
- 4. Dye & Pry (IPC‑TM‑650 2.4.57.2) performed on 2 coupons per condition; dye penetration documented.
- 5. Microsection (IPC‑TM‑650 2.1.1) performed on 2 coupons per condition; IMC thickness and void % measured.
- 6. Thermal shock (IPC‑TM‑650 2.6.7) performed on daisy‑chain coupons; cycles to failure recorded.
- 7. C‑SAM (IPC‑TM‑650 2.6.21) performed to check for delamination before and after rework.
- 8. Solder ball pull / shear (industry method) performed on passive pads; force values recorded.
- 9. All test parameters documented per TM‑650 requirements.
- 10. Comparison to baseline (0 rework) completed; report generated without applying pass/fail criteria.
Need to evaluate the reliability impact of your rework process? Our lab performs dye & pry, microsection, thermal shock, and C‑SAM per IPC‑TM‑650 to quantify rework‑induced damage.
Request Rework Reliability Testing →IPC‑TM‑650 Test Methods Referenced: 2.4.57.2 (Dye & Pry), 2.1.1 (Microsection), 2.6.7 / 2.6.7.2 (Thermal Shock), 2.6.21 (C‑SAM), 2.4.8 (Peel Strength), 2.4.52 (X‑Ray). Additional industry method: solder ball pull/shear.
Get Custom Quote
PRODUCTS CENTER


