Plating Void Inspection

Plating Void Inspection

Quality & Inspection Standards

PRODUCTS CENTER

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit
Failure Analysis IPC‑TM‑650 Class 2/3

Plating Void Inspection – IPC Class 2/3 Acceptance & Failure Analysis

Plating voids are the second most common cause of field failures after copper cracks. Unlike cracks that propagate over time, a void is a manufacturing defect present from the start – but it often goes undetected because electrical test passes when the remaining copper carries the current. We have seen 10‑layer backplanes pass 100% continuity testing yet contain wedge voids that reduced current capacity by 60%. In high‑reliability programs (Class 3), any visible void is rejectable. This guide walks through IPC‑TM‑650 microsection techniques to identify, classify, and accept or reject plating voids per IPC‑6012E.

📅 Published: May 14, 2026  |  ⏱️ 11 min read  |  🏷️ #PlatingVoid #Microsection #IPC6012

1. Plating Void Types: Wedge, Pinhole & Microvia Bottom

Per IPC‑TM‑650 Method 2.1.1, voids are classified by their location and shape. The three most critical types are:

Void Type Description Common Root Cause
Wedge void Triangular gap at innerlayer copper foil edge, inside plated hole wall Incomplete desmear, resin smear trapped under copper
Pinhole void Small isolated cavity in the barrel copper, often <0.05mm diameter Gas bubbles during plating, contaminated bath
Microvia bottom void Missing copper directly under the microvia, between via and target pad Poor laser cleaning, insufficient electroless copper deposition

Table 1: Void types referenced in IPC‑A‑600J §3.3.8 and IPC‑6018 §4.4.3.

2. Wedge Voids – The Class 3 Red Flag

Wedge voids occur at the interface between the plated copper and an innerlayer copper foil edge. Per IPC‑6012E §3.6.2.2, wedge voids are not permitted for Class 3 products under any condition. For Class 2, a wedge void is acceptable only if the remaining copper thickness in the voided area meets the minimum requirement (≥18µm for Class 2) and the void does not extend more than 5% of the hole circumference.

Root causes we have identified through process audits:

  • Incomplete desmear (plasma or permanganate) leaving resin on the innerlayer pad
  • Poor hole wall cleaning before electroless copper deposition
  • Insufficient solution agitation in high aspect ratio holes (>8:1)
  • Over‑aggressive drilling causing innerlayer smear that is not fully removed

In one aerospace program, a supplier delivered 500 panels that passed AQL microsection. During our incoming inspection, we found wedge voids in 12% of randomly sampled holes. The supplier had reduced desmear time by 20% to increase throughput. The entire lot was rejected – the cost of rework was $47,000. We now require wedge void inspection on every first article panel.

3. Pinhole Voids – Solder Blowhole Risk

Pinhole voids are small cavities within the barrel copper that do not extend to either the innerlayer or the outer surface. They are often invisible until microsection polishing reveals them. Per IPC‑A‑600J §3.3.8, pinhole voids are acceptable for Class 2 if isolated (≤3 per hole) and the total void area does not exceed 5% of the hole wall area. For Class 3, any pinhole that reduces the minimum copper thickness below 20µm is rejectable.

The real danger with pinhole voids is not electrical – it is solder blowhole. During assembly reflow, trapped plating chemistry or moisture inside the void outgasses, creating a blowhole that exposes the underlying laminate. We have seen high‑volume consumer boards with 8% blowhole defects traced directly to pinhole voids in the barrel copper. The fix required requalifying the entire plating line.

4. Microvia Bottom Voids – HDI Reliability Risk

For HDI boards, microvia bottom voids are the most critical failure mode. Per IPC‑6018 §4.4.3, the microvia must have full contact with the target pad. Any void between the microvia copper and the target pad that exceeds 10% of the via diameter is rejectable for Class 3. For Class 2, voids up to 20% of the diameter are acceptable provided the remaining contact area is ≥80%.

Microvia bottom voids are caused by:

  • Residual laser smear (charred resin) not cleaned before electroless copper
  • Insufficient electroless copper deposition on the target pad surface
  • Glass fiber protrusion after laser drilling that prevents full copper coverage

We have tested 2‑n‑2 HDI boards with microvia bottom voids at 25% of the via diameter. After 500 thermal cycles (-40°C to +125°C), 34% of the affected vias showed resistance increases >20%. The failure mechanism is current crowding through the reduced copper area, causing localized heating and eventual open circuit.

Engineering Insight

We now require microsection on three microvias per target pad type for all HDI prototypes. If a microvia bottom void exceeds 10%, we reject the panel. In one AI server program, this caught a process shift after only 15 panels – saving a $200,000 production run.

5. Acceptance Criteria: Class 2 vs Class 3

Void Type Class 2 Class 3 IPC Reference
Wedge void Accept if remaining Cu ≥18µm, void ≤5% of circumference Zero tolerance IPC‑6012E §3.6.2.2
Pinhole void (barrel) Accept ≤3 per hole, total area ≤5% of wall Accept only if thickness ≥20µm at void location IPC‑A‑600J §3.3.8
Microvia bottom void Accept if void ≤20% of via diameter Accept if void ≤10% of via diameter IPC‑6018 §4.4.3

Table 2: Void acceptance criteria with specific clause references. For wedge voids, many OEMs impose Class 3 limits on all products regardless of specified class.

Plating Void Inspection Checklist (IPC‑Anchored)

  1. Examine as‑polished condition first. Voids are visible without etching – don't rely only on micro‑etch.
  2. Classify void type. Wedge, pinhole, or microvia bottom. Acceptance differs.
  3. Measure remaining copper thickness at the void. Minimum for Class 3 is 20µm; Class 2 is 18µm per IPC‑6012E §3.6.1.1.
  4. Count voids per hole and per panel. Class 2 allows ≤5% of holes with voids; Class 3 allows zero visible voids (wedge type) per IPC‑6012E Table 4‑3.
  5. For microvias, measure void percentage. Use a calibrated reticle at 200x magnification.
  6. Check voided area for contamination. Residue inside the void indicates process failure (desmear or cleaning).
  7. Document with 200x micrograph. Include scale bar and void type annotation. Save for supplier corrective action.

6. FAQ

Q: Can a plating void be repaired?

A: No. Plating voids are irreversible manufacturing defects. The only remediation is scrapping the affected panel. This is why we recommend 100% microsection sampling on Class 3 panels during prototype phase – to catch void issues before production.

Q: How many microsections are required to detect plating voids statistically?

A: Per IPC‑6012E Table 4‑2, at least 3 coupons per panel, with 2 microsections per coupon (one as‑polished, one after thermal stress). For high‑reliability programs, we use 5 coupons per panel to achieve 95% confidence in detecting wedge voids.

Q: What causes microvia bottom voids in HDI boards?

A: The most common cause is laser smear – charred resin left on the target pad after CO₂ or UV laser drilling. If the desmear process (plasma or permanganate) is inadequate, electroless copper cannot adhere, leaving a void. Glass fiber protrusion is the second most common cause.

Q: Can electrical test detect plating voids?

A: Rarely. A single small void may not increase resistance enough to fail continuity test. However, under thermal cycling or high current, the reduced copper area can overheat and open. This is why microsection is mandatory for reliability verification.

Found plating voids in your microsections? Our engineers will review your cross‑sections against IPC‑6012 and help determine root cause – desmear, drilling, or plating chemistry.

Request Void Analysis Review →

References: IPC‑TM‑650 Method 2.1.1 §5.5.2; IPC‑6012E §3.6.1.1, §3.6.2.2, Table 4‑2; IPC‑A‑600J §3.3.8; IPC‑6018 §4.4.3. IPC‑TM‑650 Official Method.

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit