CAF Failure in PCB Design
Quality & Inspection Standards
PRODUCTS CENTER
Get Custom Quote
PRODUCTS CENTER
CAF Failure in PCB Design
Conductive anodic filament (CAF) formation is a time‑dependent, electrochemical failure that creates shorts inside the PCB. It grows silently along glass fibers, passes electrical test, and then fails in the field after hundreds of hours under voltage, humidity, and temperature. This article explains the physics, the design rules that prevent CAF, and the IPC‑6012E test requirements.
Table of Contents
1. The CAF Formation Mechanism
CAF is an electrochemical migration process that occurs along the interface between glass fibers and resin. It requires four simultaneous conditions:
- An anode and cathode — typically two plated through‑holes or conductors at different potentials.
- A conductive path — the glass‑fiber‑resin interface provides a microscopic channel for ion transport.
- An electrolyte — absorbed moisture in the laminate.
- A driving voltage — the potential difference between conductors.
At the anode, copper oxidizes to Cu²⁺ ions. These ions migrate along the glass‑fiber‑resin interface toward the cathode, where they are reduced back to metallic copper. Over time, a conductive filament grows from the cathode toward the anode, eventually bridging the gap and creating a resistive short.
Key Insight
CAF is not a dielectric breakdown. It is an electrochemical corrosion process. The filament grows atom‑by‑atom, not in a single event. This is why a board can pass 100% electrical test at time‑zero and fail 500 hours later in the field.
2. Four Drivers of CAF Growth
| Driver | Effect on CAF | Design Lever |
|---|---|---|
| Conductor spacing | CAF time‑to‑failure decreases exponentially with reduced spacing | Minimum 0.15 mm wall‑to‑wall for vias |
| Voltage gradient | Higher voltage accelerates ion migration | Limit voltage between adjacent vias |
| Humidity / moisture | Moisture provides the electrolyte; CAF stops below 60% RH | Pre‑bake; conformal coating |
| Glass‑weave style | Loose weaves create open channels; tight weaves restrict them | Specify 1080 or 106 glass style |
Table 1: The four drivers of CAF and their design levers.
3. Design Rules to Prevent CAF
CAF is a design‑preventable failure. The following rules are derived from IPC‑6012E and industry reliability data:
- Minimum via‑to‑via spacing: 0.15 mm wall‑to‑wall. This is the single most effective design rule. At 0.15 mm, the time‑to‑failure under standard CAF test conditions is typically > 1000 hours.
- Avoid routing high‑voltage and low‑voltage signals in adjacent vias. The voltage gradient is the accelerator. Group similar‑voltage vias together.
- Specify tight‑weave glass styles. 1080 and 106 glass have higher thread counts than 2116 or 7628. The tighter the weave, the less open space between fibers for CAF growth.
- Use high‑resin‑content prepreg. A resin‑rich bond line encapsulates the glass fibers, blocking the conductive path. Prepreg with ≥ 55% resin content is recommended.
4. CAF Testing & IPC‑6012E Requirements
Per IPC‑6012E §6.3, CAF resistance must be demonstrated when specified on the procurement document. The standard test conditions are:
- 85 °C / 85% RH environment.
- 100 V DC bias applied continuously.
- 1000‑hour duration minimum.
- Insulation resistance must not drop below 10⁸ Ω during the test.
The test is performed on a representative coupon with the same layer stackup, via spacing, and materials as the production board. Any coupon that shows a resistive drop below the threshold is cause for lot rejection.
Design Rule
If your design has via‑to‑via spacing below 0.15 mm, CAF testing per IPC‑6012E §6.3 is not optional — it is mandatory. The fabricator must provide CAF test data for the specific stackup and spacing used.
5. Material & Process Prevention
- Use CAF‑resistant laminates. Materials with modified epoxy formulations (e.g., phenolic‑cured or dicy‑free) have inherently lower CAF susceptibility. Ask the laminate supplier for CAF test data.
- Pre‑bake laminates before lamination. Moisture absorbed during storage can be trapped inside the board. Pre‑bake at 125 °C for 4 hours removes this moisture.
- Optimize drilling parameters. Excessive drill wear creates rough hole walls that expose glass fibers, providing CAF initiation sites. Use new drills and controlled feed rates.
- Ensure complete desmear. Resin smear left on the hole wall after drilling creates a porous layer that accelerates moisture absorption. Plasma desmear is preferred for high‑reliability boards.
6. FAQ
Q: Can CAF occur in low‑voltage circuits (3.3 V)?
A: Yes, but the time‑to‑failure is longer. CAF is driven by the electric field gradient, not absolute voltage. At tight spacings (< 0.1 mm), even 3.3 V can drive CAF over sufficient time.
Q: Is CAF reversible?
A: No. Once the copper filament has formed, it is permanent. The only remediation is board replacement. Prevention is the only viable strategy.
Q: How does HDI design affect CAF risk?
A: HDI increases CAF risk significantly. Laser‑drilled vias expose glass fibers on the via wall, creating ready‑made pathways. Tighter via spacing and thinner dielectrics in HDI both accelerate CAF.
CAF Prevention Checklist
- Maintain via‑to‑via spacing ≥ 0.15 mm wall‑to‑wall.
- Specify tight‑weave glass style (1080 or 106).
- Use prepreg with resin content ≥ 55%.
- Pre‑bake laminates at 125 °C for 4 hours before lamination.
- Require CAF testing per IPC‑6012E §6.3 for designs with spacing < 0.15 mm.
- Use plasma desmear after drilling for high‑reliability boards.
- Group similar‑voltage vias together; separate high‑voltage from low‑voltage.
Continue Reading
Concerned about CAF risk in your PCB design? Submit your stackup for a reliability review.
Request Engineering Review →References: IPC‑6012E §6.3 (CAF Testing), IPC‑TM‑650 (Insulation Resistance), IPC‑4101 (Base Materials). IPC Online Standards.
Get Custom Quote
PRODUCTS CENTER


