Prepreg Selection in Multilayer PCB
Quality & Inspection Standards
PRODUCTS CENTER
Get Custom Quote
PRODUCTS CENTER
Prepreg Selection in Multilayer PCB
Prepreg is the “glue” that bonds cores together, but in high‑speed design it is also the dielectric that sets impedance, controls loss, and determines lamination quality. A wrong prepreg choice leads to voids, thickness variation, and impedance drift across the panel.
Table of Contents
1. The Dual Role of Prepreg in a Multilayer Stackup
Prepreg (pre‑impregnated fiberglass cloth with partially cured resin) serves two critical functions in every multilayer PCB:
- Bonding agent: under heat and pressure, the resin flows, fills gaps between copper features, and permanently laminates adjacent cores or foils together.
- Dielectric layer: once cured, the prepreg becomes the insulating material between copper layers. Its thickness and dielectric constant (Dk) define the impedance of traces that reference across it.
The challenge is that bonding demands sufficient resin flow, while impedance control demands precise, consistent thickness. Selecting the right prepreg style and resin content balances both requirements.
2. Prepreg Composition: Glass Weave & Resin Systems
Every prepreg is defined by three elements:
- Glass fabric style — the weave pattern and thread count (106, 1080, 2113, 2116, 7628, etc.). This dictates the minimum thickness and the resin‑to‑glass ratio.
- Resin system — the polymer chemistry (epoxy, polyimide, BT, PPE, PTFE). This determines the Dk, Df, Tg (glass transition temperature), Td (decomposition temperature), and Z‑axis CTE.
- Resin content (RC%) — the weight percentage of resin in the prepreg. Higher RC improves gap‑filling but increases thickness variation. Typical values range from 40% (low‑flow) to 75% (high‑flow).
| Property | FR‑4 (Epoxy) | Mid‑Loss (PPE/PPO) | Ultra‑Low‑Loss (PTFE/PPE) |
|---|---|---|---|
| Dk @ 1 GHz | 4.2–4.6 | 3.5–3.9 | 3.0–3.5 |
| Df @ 1 GHz | 0.020–0.025 | 0.004–0.008 | 0.001–0.003 |
| Tg (°C) | 130–170 | 170–200 | 200–280 |
| Z‑CTE (ppm/°C) | 50–70 | 35–50 | 25–40 |
Table 1: Typical prepreg material families. Source: IPC‑4101/4103 slash sheets.
3. Glass Style Selection & Thickness Control
The glass fabric style determines the minimum achievable prepreg thickness and the resin‑glass ratio. Key styles:
| Glass Style | Typical Thickness (mil) | Resin Content Range | Best Application |
|---|---|---|---|
| 106 | 1.5–2.0 | 60–75% | Thin dielectrics, fine pitch |
| 1080 | 2.5–3.0 | 55–65% | General impedance layers |
| 2113 | 3.5–4.5 | 45–55% | 2‑layer bonding, thicker gaps |
| 2116 | 4.0–5.5 | 40–50% | Power‑plane spacing |
| 7628 | 7.0–8.5 | 35–45% | Thick cores, high‑current boards |
Table 2: Common glass styles. Thickness ranges assume single ply; multiple plies can be combined for thicker dielectrics.
For thin dielectrics (≤ 3 mil), a single ply of 106 or 1080 glass is required. When impedance tolerance is tight, specify the glass style explicitly on the fabrication drawing to limit thickness variation.
4. Impact on Impedance and Signal Integrity
In a multilayer stackup, prepreg layers carry the critical dielectric thickness (H) used in impedance calculations. Two factors make prepreg selection an impedance‑control decision:
- Thickness tolerance: a ±0.5 mil variation in a 4‑mil prepreg layer can shift a 50 Ω microstrip by 3–5 Ω. Multi‑ply constructions reduce this variation because the plies average out thickness differences.
- Resin‑rich vs. glass‑rich regions: glass cloth has a higher Dk (~6.0) than the surrounding resin (~3.0–3.5). Traces that align with glass bundles see a different effective Dk than those in resin‑rich areas. This is the glass‑weave skew effect — it can introduce 2–5 ps/in of differential skew in high‑speed pairs. Solutions include rotating the routing matrix, using spread‑glass fabric, or specifying a higher resin content prepreg.
Design Rule
Request the fabricator’s measured prepreg thickness after lamination (not the nominal uncured thickness) for your field‑solver model. Use the same glass style for identical functions across the panel — never mix 106 and 1080 on a layer that expects the same impedance.
5. Lamination Process: Resin Flow, Voids & Bond Strength
During lamination, the prepreg resin melts, flows, and cures. Insufficient flow leaves voids (air gaps) between copper features; excessive flow causes resin starvation and thickness collapse.
5.1 Void Prevention
Voids are the most common lamination defect. They concentrate electric field and can cause partial discharge at high voltage, plus impedance discontinuity. Prevention requires:
- Adequate resin content — for high‑copper‑density areas (e.g., under BGAs), select a prepreg with ≥ 60% RC or use multiple plies.
- Proper pressure and temperature ramp per the resin manufacturer’s profile.
- Pre‑baking prepreg to remove moisture before lamination.
5.2 Resin Recess and Conductor Filling
When laminating over patterned copper, the resin must fill the gaps between conductors. A common rule: the prepreg resin thickness after lamination should be at least 1.5× the copper thickness it covers. For 1 oz copper (1.4 mil), a minimum resin thickness of 2.1 mil is needed — this typically requires a 106 or 1080 prepreg with high RC.
5.3 Z‑Axis Expansion and Reliability
Z‑axis CTE causes barrel cracking in plated through‑holes. The prepreg’s Z‑CTE depends primarily on the resin system. For high‑reliability Class 3 boards, choose a prepreg with Z‑CTE ≤ 50 ppm/°C and Tg ≥ 170 °C. This information is available in the material supplier’s IPC‑4101 slash sheet.
6. DFM: Specifying Prepregs for Reliable Production
A fabricator‑ready stackup drawing includes the following prepreg specifications:
- Glass style and number of plies — e.g., “One ply 1080 + one ply 2113” yields ~6.5 mil total.
- Resin content percentage — or specify “high‑flow” or “low‑flow” per IPC‑4101 classes.
- Target pressed thickness — not the raw prepreg thickness. Ask the fabricator for their stackup chart with pressed thickness data.
- Material brand / type — when a specific Dk/Df is needed, name the laminate family (e.g., Megtron 6, Rogers 4350B, Isola I‑Tera MT40) so the fabricator sources the correct slash sheet.
- IPC‑6012 class — Class 2 or 3, which governs acceptance criteria for voids, delamination, and dielectric spacing.
According to IPC‑6012E §3.6.2.18, the minimum dielectric spacing through prepreg between adjacent copper layers is 90 µm (3.5 mil) unless otherwise specified. For high‑speed designs using thin dielectrics, specify the target and tolerance explicitly.
Prepreg Selection Checklist
- ☑️ Choose glass style based on target dielectric thickness and tolerance.
- ☑️ Select resin content sufficient to fill copper gaps without resin starvation.
- ☑️ Match Dk/Df to the required performance class (low‑loss for ≥ 5 Gbps).
- ☑️ Avoid glass‑weave skew by routing at 7‑10° angle or using spread glass.
- ☑️ Specify pressed thickness — not raw prepreg thickness.
- ☑️ Validate Z‑CTE and Tg for the required reliability class (Class 2 or 3).
- ☑️ Request fabricator’s stackup data with measured dielectric constants.
- ☑️ Review IPC‑6012E §3.6.2.18 for minimum dielectric spacing.
Continue Reading
Need help selecting the right prepreg for your impedance‑controlled stackup?
Request Engineering Review →References: IPC‑4101 (Base Materials), IPC‑4103 (High‑Speed/High‑Frequency Materials), IPC‑6012E §3.6.2.18 (Dielectric Spacing), IPC‑4412 (Prepreg Requirements), IPC Online Resources.
Get Custom Quote
PRODUCTS CENTER


