Via-in-Pad Reliability Validation
Quality & Inspection Standards
PRODUCTS CENTER
Get Custom Quote
PRODUCTS CENTER
Via-in-Pad Reliability Validation – Filling, Copper Capping & IPC Requirements
Via-in-pad (VIP) is often a necessity for fine‑pitch BGAs (≤0.5mm). But an unfilled or poorly capped via-in-pad is a reliability disaster waiting to happen. We have seen BGA assemblies with unfilled VIP where solder wicked into the via, leaving insufficient solder volume for the joint. We have also seen copper caps that were too thin (<12µm) crack during reflow, creating a void under the ball. IPC‑6012E §3.3.4 requires that vias in solderable pads be filled and capped for Class 3. This guide covers filling materials (conductive vs non‑conductive), copper capping thickness requirements, inspection criteria (voids, dimple height), and qualification testing to ensure VIP reliability.
Table of Contents
- Why Fill and Cap – Solder Wicking, Voiding & Planarity
- Filling Materials – Conductive vs Non‑Conductive
- Copper Capping – Thickness, Process & Acceptance
- Failure Modes – Cracks, Delamination, Voids
- Inspection Criteria – Microsection, Planarity & Void Limits
- Qualification Testing – Thermal Stress, Shock & SIR
- Via-in-Pad Reliability Checklist
- FAQ – Via-in-Pad Reliability
1. Why Fill and Cap – Solder Wicking, Voiding & Planarity
An unfilled via under a BGA pad creates three reliability risks:
- Solder wicking: Molten solder flows into the via barrel, starving the joint. Result: head‑in‑pillow defect, intermittent connection, or open.
- Outgassing voids: Trapped air or plating chemistry expands during reflow, creating a large void in the solder joint. Reduces mechanical strength and current carrying capacity.
- Non‑planarity: The via depression causes the BGA ball to tilt, leading to uneven joint height and increased stress on adjacent balls.
For Class 3, IPC‑6012E §3.3.4 explicitly requires that vias located in solderable pads (such as BGA landing pads) be filled and capped. For Class 2, unfilled vias may be permitted if the via diameter is small (<0.3mm) and the pad size is large enough to keep the via away from the ball center, but this is risky.
In a medical device program, the supplier left a 0.2mm via unfilled under a 0.4mm BGA pad. X‑ray inspection after assembly showed large voids in 12% of joints. The boards were scrapped. The lesson: fill and cap is not optional for fine‑pitch BGAs.
2. Filling Materials – Conductive vs Non‑Conductive
Two types of via fill are common. The choice affects electrical performance, thermal conductivity, and cost.
| Fill Type | Material | Electrical Property | Cost | Typical Use |
|---|
Non‑conductive epoxy fill is the industry standard for VIPPO (Via‑in‑Pad Plated Over). The epoxy is screen‑printed or vacuum‑filled into the via, then cured. After curing, the panel is over‑plated with copper, which bonds to the epoxy and forms a solid cap.
Conductive copper paste fill is used when the via carries significant current or needs to dissipate heat. However, copper paste has higher CTE (≈80‑120 ppm/°C) than epoxy (≈30‑50 ppm/°C), increasing stress on the cap during thermal cycling. We have seen conductive filled vias crack more often than epoxy filled.
3. Copper Capping – Thickness, Process & Acceptance
The copper cap is the final plated layer over the filled via. It provides a flat, solderable surface. Per IPC‑6012E §3.3.4, the minimum copper cap thickness for Class 3 is 12µm. For Class 2, 5µm is typical but not recommended for fine‑pitch BGAs.
The cap is formed by electroplating after the fill is cured and surface planed. Key process requirements:
- Cap thickness must be measured at the thinnest point over the via (usually the edge, not the center).
- Dimple (concavity) or protrusion (convexity) must be ≤25µm relative to the surrounding pad surface. Excessive dimple traps flux; excessive protrusion lifts the BGA ball.
- Adhesion between the cap and the fill material must survive thermal stress. Delamination appears as a dark line under the cap.
In one HDI qualification, we measured cap thickness on 100 vias. The supplier’s specification was 15µm minimum, but we found 8µm at the edges due to uneven plating current distribution. After revising the panel layout (adding dummy features for current balance), thickness uniformity improved to ±3µm. Cap thickness is a process capability issue, not just a design rule.
4. Failure Modes – Cracks, Delamination, Voids
Via‑in‑pad structures can fail in several ways during assembly or field life.
- Cap cracking at the via edge: Stress concentration at the 90° corner of the via. Caused by CTE mismatch between copper cap (17 ppm/°C), fill material (30‑120 ppm/°C), and dielectric (50‑200 ppm/°C). Cracks appear radially outward from the via edge. Rejectable for Class 3 if crack reaches the BGA pad center.
- Delamination between cap and fill: Poor adhesion or contamination during plating. Appears as a dark horizontal line in microsection. Zero tolerance for Class 3.
- Fill material shrinkage voids: Large voids in the epoxy fill (>50% of via volume) cause the cap to sag, creating a dimple that traps flux. Limit: maximum void volume 20% per IPC‑6012.
- Plating voids in the cap: Incomplete copper coverage, often at the edge of the via. Class 3 zero tolerance.
A telecom board with VIPPO on 0.5mm BGA passed initial inspection but after 500 thermal cycles, 8% of vias showed cap cracks. The root cause was a fill material with CTE 100 ppm/°C (too high). Switching to a low‑CTE fill (40 ppm/°C) eliminated cracks.
5. Inspection Criteria – Microsection, Planarity & Void Limits
Inspection of via‑in‑pad structures requires both microsection and surface profilometry.
| Parameter | Class 2 | Class 3 | IPC Reference |
|---|---|---|---|
| Copper cap thickness (min) | 5µm (not recommended for BGA) | 12µm | IPC‑6012E §3.3.4 |
| Dimple / protrusion (max) | ±50µm | ±25µm | AABUS (customer spec) |
| Cap crack length | ≤10% of via circumference | Zero | IPC‑6018 §5.2 |
| Delamination (cap‑fill) | Accept if ≤5% of area, isolated | Zero | IPC‑6018 §5.2 |
| Fill void volume | ≤30% | ≤20% | Common OEM limit |
Microsection at 200‑500x is required to measure cap thickness, detect cracks, and identify delamination. For planarity, use a laser profilometer or a dial indicator over a sampling of pads.
6. Qualification Testing – Thermal Stress, Shock & SIR
Via‑in‑pad reliability must be validated with the same tests as other microvias, plus additional checks for cap integrity.
- Thermal stress (IPC‑TM‑650 2.4.13.1): 288°C solder float, 10 seconds. Checks for gross delamination and cap cracking.
- Thermal shock (IPC‑TM‑650 2.6.7.2): 500 cycles minimum for Class 3 (-40°C to +125°C). Examine at 500x for cracks at via edges.
- Reflow simulation (IPC‑TM‑650 2.6.27): 5 cycles of lead‑free profile. Simulates assembly and rework.
- Microsection after testing: Measure cap thickness again — no thinning allowed. Any crack or separation is failure for Class 3.
In a medical device qualification, the supplier passed thermal stress but failed thermal shock at 300 cycles (cap cracks). The root cause was insufficient cap thickness (8µm vs 12µm requirement). After correcting plating parameters, the same design passed 1000 cycles.
Via-in-Pad Reliability Checklist
- Specify filled + capped for all vias under BGA pads. Unfilled VIP is not allowed for Class 3.
- Require non‑conductive epoxy fill with CTE ≤50 ppm/°C. High‑CTE fill causes cap cracks.
- Set minimum copper cap thickness to 12µm (Class 3) or 5µm (Class 2) per IPC‑6012E §3.3.4.
- Specify dimple/protrusion ≤25µm. Use laser profilometry on a sampling plan.
- Require microsection on 3 coupons per panel. Inspect at 200‑500x for cap thickness, voids, cracks, delamination.
- Qualify with thermal shock (500 cycles min for Class 3). Reject if any cap cracks appear.
- Audit the supplier's plating current distribution. Edge vias often have thinner caps.
Continue Reading – HDI & Microvia Series
FAQ – Via-in-Pad Reliability
Q: Is filling required for all vias under BGAs or only for Class 3?
A: IPC‑6012E §3.3.4 requires filling for Class 3. For Class 2, unfilled vias may be acceptable if the via is small (≤0.2mm) and the pad is large enough to keep the via away from the ball center. However, most OEMs require filling for all BGA pads regardless of class.
Q: Can I use conductive copper paste fill for all vias?
A: Yes, but copper paste has higher CTE (80‑120 ppm/°C) than epoxy (30‑50 ppm/°C), increasing stress on the cap. It also costs more. Use conductive fill only when the via carries current or requires thermal conductivity.
Q: What is the typical yield loss for VIPPO process?
A: With a mature supplier, yield for VIPPO is 95‑98%. Common defects: voids in fill (2‑3%), cap thickness variation (2‑3%), dimple out of spec (1‑2%).
Q: How do I inspect dimple height without a profilometer?
A: You can use a dial indicator with a flat probe on a sampling basis (e.g., 10 pads per panel). For high‑volume production, a laser profilometer is recommended.
Need help specifying via‑in‑pad requirements for your BGA design? Our engineers will review your pad stack, fill material, cap thickness, and qualification plan per IPC‑6012.
Request VIPPO Design Review →References: IPC‑6012E §3.3.4; IPC‑6018 §5.2; IPC‑TM‑650 2.4.13.1, 2.6.7.2, 2.6.27. IPC‑TM‑650 Official Method.
Get Custom Quote
PRODUCTS CENTER


