IPC‑6012 Class 3 Compliance Checklist
Class 3 is the highest reliability tier in IPC‑6012, reserved for aerospace, defence, medical, and other mission‑critical applications where downtime is not permitted. Use this checklist to verify that your rigid PCB design, procurement specification, and incoming inspection criteria fully address every Class 3 requirement defined in the standard.
Download the full printable checklist (PDF)
One‑page summary for your design review meetings and supplier audits.
Download Checklist (PDF) →
1. Base Materials & Copper Foil
☐ Laminate material specified per IPC‑4101 or IPC‑4103 (for PTFE/high‑frequency); epoxy glass is the default (IPC‑6012E §3.2.1).
☐ Copper foil type, grade, weight, and profile defined per IPC‑4562 (§3.2.4).
☐ Metal core or external heat sink materials (if used) conform to Table 3‑1 (§3.2.5).
☐ Embedded passive materials (if used) meet IPC‑4811 or IPC‑4821 (§3.2.14).
2. Copper Plating Thickness (PTH & Via)
☐ PTH average copper ≥ 25 µm; minimum ≥ 20 µm (Table 3‑4, §3.6.2.11).
☐ Microvia average copper ≥ 12 µm; minimum ≥ 10 µm (Table 3‑5).
☐ Buried core (2‑layer) average copper ≥ 15 µm; minimum ≥ 13 µm (Table 3‑6).
☐ Wrap plating ≥ 12 µm extending ≥ 25 µm from via edge (for designs after 2018‑01‑01) (Table 3‑4, §3.6.2.11.1).
☐ Copper purity ≥ 99.50%; tensile strength ≥ 248 MPa; elongation ≥ 12% (§3.2.6.2).
Manufacturing consideration: Class 3 compliance depends on controlling finished hole copper, wrap plating, registration and process consistency across production—not only meeting nominal design values. Review our
PCB manufacturing capabilities for fabrication, plating, inspection and process-control support.
3. Annular Ring & Breakout
☐ External PTH annular ring ≥ 50 µm; no breakout permitted (Table 3‑9).
☐ Internal annular ring ≥ 25 µm; no breakout (Table 3‑9, §3.6.2.9).
☐ Microvia capture pad: no breakout on target pad (Table 3‑9, §3.6.2.9.2).
☐ Non‑supported hole annular ring ≥ 150 µm (Table 3‑9).
☐ Teardrop or fillet use on Class 3 requires AABUS (agreement between user and supplier) (§3.4.2).
4. Plating Integrity After Thermal Stress
☐ No copper plating voids in any hole after thermal stress (Table 3‑10, §3.6.2.2).
☐ No internal separation at inner‑layer / hole‑wall interface (Table 3‑10, §3.6.2.1).
☐ No B‑type or D‑type copper cracks in outer foil; no C‑type cracks in inner foil (Table 3‑10).
☐ No E‑type or F‑type cracks in hole‑wall or corner plating (Table 3‑10).
☐ No delamination or blister on microsection (Table 3‑10, §3.6.2.5).
☐ No negative etchback when positive etchback is specified (§3.6.2.8).
☐ Wicking maximum: 80 µm (Table 3‑10).
☐ Laminate voids: ≤ 80 µm outside the “zone of heat” (§3.6.2.3, Figure 3‑13).
5. Via Fill & Cap Plating
☐ Filled via copper cap ≥ 12 µm (Table 3‑11, §3.6.2.11.2).
☐ Via fill depression (dimple) ≤ 76 µm; protrusion ≤ 50 µm (Table 3‑11).
☐ Copper‑filled microvia: sealed voids only, ≤ 25% of visible area (Table 3‑12, §3.6.2.11.3).
☐ Non‑conductive fill: fill ≥ 60% of hole volume (§3.6.2.19).
☐ Cap‑to‑underlying‑plating separation: not permitted (§3.6.2.11.2, Figure 3‑30).
6. Microvia Requirements
☐ Microvia aspect ratio ≤ 1:1; depth ≤ 0.25 mm (§1.4.4).
☐ Target pad contact ≥ 50% continuous; no inclusions (Table 3‑12, §3.6.2.12).
☐ Target pad penetration: must not reduce dielectric spacing below minimum (§3.6.2.13).
☐ Consider performance‑based testing per IPC‑TM‑650 Method 2.6.27 for microvia reliability (§3.10.15).
7. Conductor Width, Spacing & Defects
☐ Conductor width reduction ≤ 20% of minimum specified width (§3.5.3.1).
☐ Conductor thickness reduction ≤ 20% of minimum specified thickness (§3.5.3.2).
☐ Spacing reduction due to processing ≤ 20% (§3.5.2).
☐ Defect‑area equivalent cross‑section reduction ≤ 20% of minimum; total defect length ≤ 10% of conductor length or 13 mm, whichever is smaller (§3.5.3).
☐ Exposed metal on non‑solderable areas ≤ 1% of conductor surface (§3.5.4.7.1).
☐ Bow & twist: ≤ 0.75% for SMT boards; ≤ 1.5% for all others (§3.4.3).
8. Visual Inspection (Prior to Microsection)
☐ No copper plating voids visible in any hole (§3.3.3, Table 3‑7).
☐ Final finish voids: ≤ 1 void per hole, ≤ 5% of holes affected (Table 3‑7).
☐ No lifted lands on delivered boards (§3.3.4).
☐ No exposed weave (§3.3.2.5).
☐ Dewetting on solderable lands ≤ 5% (§3.5.4.5).
☐ Edge connector gold overlap/gap: ≤ 0.8 mm (Table 3‑8).
9. Electrical & Environmental Testing
☐ Continuity & isolation: per IPC‑9252; recommended 100% electrical test for Class 3 (§3.8.2).
☐ Dielectric withstand: 500 V DC (spacing ≥ 80 µm) or 250 V DC (spacing < 80 µm), 30 s (Table 3‑17, §3.8.1).
☐ Insulation resistance after MIR: ≥ 500 MΩ (Table 3‑18, §3.8.4).
☐ Ionic cleanliness: ≤ 1.56 µg/cm² NaCl equivalent per IPC‑TM‑650 Method 2.3.25 (§3.9).
☐ Solder mask: IPC‑SM‑840 Class H required for Class 3 (§3.7).
10. Quality Assurance & Sampling
☐ Thermal stress test method specified (2.6.8 or 2.6.27) (§1.3.3).
☐ A & B test coupons on every panel; one in X‑axis, one in Y‑axis (§3.6, §4.3.1).
☐ C=0 sampling per Table 4‑2; plan determined by lot size and AQL (§4.2.1).
☐ Structural integrity: microsection at 100× initial / 200× arbitration (§3.6.1.5).
☐ Quality conformance testing (Group B) per Table 4‑4 – monthly for copper plating properties (§4.3).
Related Manufacturing Capability
PCB Manufacturing Capabilities
Controlled fabrication, plating, inspection, electrical testing and process verification for high-reliability PCB production requirements.
Review Your PCB Against IPC-6012 Class 3 Requirements
If your project requires Class 3 compliance, submit the fabrication requirements, stackup and applicable inspection or qualification criteria for a manufacturing and compliance review before production release.
Request a Class 3 Compliance Review
References: IPC‑6012E (2020), Sections 1.3.1, 1.4.4, 3.2, 3.3, 3.4, 3.5, 3.6, 3.7, 3.8, 3.9, 3.10, 4. Tables 3‑4, 3‑5, 3‑6, 3‑7, 3‑8, 3‑9, 3‑10, 3‑11, 3‑12, 3‑17, 3‑18, 4‑2, 4‑4. Courtesy of IPC.