HiPot Testing
Quality & Inspection Standards
PRODUCTS CENTER
Get Custom Quote
PRODUCTS CENTER
HiPot Testing – Dielectric Withstand Voltage, IPC‑TM‑650 2.5.7 & PCB Insulation Reliability
HiPot (high potential) testing is the only method to verify that a PCB’s dielectric insulation can withstand high voltage without breakdown. Unlike continuity or isolation resistance tests (which use low voltage, typically ≤500V DC), HiPot applies a stress voltage significantly higher than the operating voltage — often 1,000‑2,000V AC or DC — to expose weak spots: delamination, CAF filaments, insufficient creepage, or contamination. We have seen power supply boards that passed isolation resistance at 250V but failed HiPot at 1,500V due to a 10µm delamination gap that only broke down under stress. IPC‑TM‑650 2.5.7 (Dielectric Withstanding Voltage, PCB) and 2.5.7.1 (Dielectric Withstanding Voltage, Conformal Coating) define the test methods. This UltroNiu engineering specification establishes HiPot test requirements: test voltage (typically 2× operating voltage + 1,000V for AC mains), ramp rate, dwell time, leakage current limits, and acceptance criteria for Class 2/3, automotive, and aerospace. Use this guide to specify HiPot testing in your procurement document and prevent field arcing or dielectric breakdown.
Table of Contents
- Purpose – Why HiPot Is Required Beyond Isolation Resistance
- Failure Mode – Test Matrix (Dielectric Breakdown)
- Test Method – IPC‑TM‑650 2.5.7 / 2.5.7.1
- Test Voltage Selection – By Operating Voltage & Standard
- Acceptance Criteria – Leakage Current, Arc Detection & Breakdown
- Application‑Based Decision Table
- Common HiPot Failures & Root Causes
- Safety & Fixturing Requirements
- Sampling & Documentation
- FAQ – HiPot Testing
- HiPot Test Specification Checklist
1. Purpose – Why HiPot Is Required Beyond Isolation Resistance
Isolation resistance testing (IPC‑TM‑650 2.5.17) measures DC resistance at relatively low voltage (typically 100‑500V). It can miss defects that only break down at higher stress voltages. HiPot testing applies a voltage significantly higher than operating voltage (e.g., 1,500V AC for a 230V mains circuit) and measures leakage current. It detects:
- Dielectric breakdown: Arcing through delamination, voids, or carbonized paths.
- Insufficient creepage/clearance: Inadequate spacing between high‑voltage nets.
- Contamination-induced tracking: Ionic residues that become conductive at high voltage.
- Conformal coating defects: Pinholes or cracks that reduce dielectric strength.
For any PCB with operating voltage >50V DC or 30V AC, HiPot testing SHALL be performed as part of qualification. For mains‑connected circuits (100‑240V AC), HiPot testing is mandatory per safety standards (IEC 60950, UL 60950).
2. Failure Mode – Test Matrix (Dielectric Breakdown)
| Failure Mode | Root Cause | HiPot Signature | Acceptance |
|---|---|---|---|
| Dielectric breakdown (arc)<\/td> | Delamination, CAF filament, void in laminate<\/td> | Sudden leakage current spike >limit<\/td> | Reject (no breakdown allowed)<\/td> |
| Excessive leakage current (no breakdown)<\/td> | Surface contamination (ionic residues), moisture<\/td> | Leakage current gradually rises but no arc<\/td> | Reject if exceeds limit, may clean and retest<\/td> |
| Conformal coating breakdown<\/td> | Pinhole, insufficient thickness, porosity<\/td> | Arc through coating at lower voltage than expected<\/td> | Reject; coating must withstand specified voltage<\/td> |
| Creepage\/clearance violation<\/td> | Traces too close, no slot, sharp corners<\/td> | Arc between conductors at voltage below design margin<\/td> | Design change required<\/td> |
3. Test Method – IPC‑TM‑650 2.5.7 / 2.5.7.1
IPC‑TM‑650 2.5.7 specifies the dielectric withstand test for printed boards. Key parameters:
- Test voltage waveform: AC (50/60 Hz) or DC. AC is more common for safety compliance because it stresses both polarities. DC may be used for high‑voltage circuits to avoid capacitive charging current.
- Ramp rate: Typically 500 V/s (10‑20 seconds to reach test voltage).
- Dwell time: 60 seconds (typical for qualification), 1‑5 seconds for production testing (per IPC‑6012E).
- Leakage current limit: For bare boards, ≤5 mA (or as specified). For assembled boards, ≤1‑2 mA common.
- Test points: Apply between each net and all other nets (or between groups). For production testing, test between power and ground, and between high‑voltage nets and chassis.
- Arc detection: HiPot tester SHALL detect arcs (sudden current spikes) and stop the test, reporting failure.
For conformal coated boards, use IPC‑TM‑650 2.5.7.1 with the same parameters but test through the coating. Accept if no breakdown and leakage current ≤10 µA (typical for high‑quality coating).
4. Test Voltage Selection – By Operating Voltage & Standard
Test voltage SHALL be determined by the product’s operating voltage and applicable safety standard. The table below provides typical values.
| Operating Voltage (V) | Test Voltage (AC, 60s) | Test Voltage (DC, 60s) | Applicable Standard |
|---|---|---|---|
| ≤30V (SELV)<\/td> | Not required (typically)<\/td> | Not required<\/td> | May be omitted for low voltage<\/td> |
| 50‑125V DC<\/td> | 500V AC<\/td> | 700V DC<\/td> | IPC‑6012E, UL<\/td> |
| 100‑240V AC (mains)<\/td> | 1,500V AC (1,250V for production)<\/td> | 2,120V DC<\/td> | IEC 60950, UL 60950<\/td> |
| 400V DC (automotive HV)<\/td> | Not common (use DC)<\/td> | 2,500V DC<\/td> | LV 123, ISO 6469<\/td> |
| 600V DC (industrial)<\/td> | —<\/td> | 3,500V DC<\/td> | IEC 61800‑5‑1<\/td> |
For custom designs, use 2× operating voltage + 1,000V (AC) or 2.8× operating voltage for DC (per IPC‑2221). For Class 3, test voltage SHALL be at least 500V AC or 700V DC even for low‑voltage circuits to catch creepage issues.
5. Acceptance Criteria – Leakage Current, Arc Detection & Breakdown
Pass/fail criteria SHALL be defined as follows:
- No dielectric breakdown (arc or flashover): The board SHALL withstand the test voltage for the specified dwell time without arcing, sparking, or breakdown. Any arc detected is a failure.
- Leakage current limit: For bare boards, leakage current SHALL be ≤5 mA (AC) or ≤10 µA (DC) typical. For assembled boards with components, leakage current may be higher due to Y‑capacitors; set limit per product safety standard (e.g., ≤5 mA for IEC 60950).
- No excessive partial discharge (for >1,000V AC): For high‑voltage applications, partial discharge testing may be required (not covered here).
- After test: The board SHALL show no visible damage (carbonized tracks, melted solder mask, or discoloration).
If a board fails HiPot due to contamination (excessive leakage but no arc), it may be cleaned and retested once. If it fails again, reject the lot.
6. Application‑Based Decision Table
| Application / Operating Voltage | HiPot Required? | Test Voltage (AC, 60s) | Sampling |
|---|---|---|---|
| ≤30V (SELV, Class 2/3)<\/td> | Optional (recommended for Class 3)<\/td> | 500V AC<\/td> | 1 per lot<\/td> |
| 50‑125V (industrial control)<\/td> | SHALL<\/td> | 500V AC (1,000V for Class 3)<\/td> | 3 per lot<\/td> |
| 100‑240V AC (mains power)<\/td> | SHALL (safety standard)<\/td> | 1,500V AC (1,250V production)<\/td> | 100% panels<\/td> |
| Automotive HV (400V DC)<\/td> | SHALL<\/td> | 2,500V DC (or 2× operating + 1,000V)<\/td> | 100% panels<\/td> |
7. Common HiPot Failures & Root Causes
- Arc between adjacent conductors: Insufficient creepage/clearance (typically <2mm for 1,500V AC). Root cause: layout violation. Fix: increase spacing, add slots, or use conformal coating.
- Breakdown through laminate: Delamination, CAF, or internal void. Root cause: poor lamination, moisture absorption. Mitigation: improve lamination process, bake boards before test.
- High leakage current (no arc): Surface contamination (flux residues, fingerprints). Root cause: inadequate cleaning. Mitigation: clean and retest.
- Corona / partial discharge at connector pins: Sharp points or inadequate potting. Root cause: design. Mitigation: round pads, add solder mask over sharp corners.
8. Safety & Fixturing Requirements
HiPot testing involves high voltage and presents a shock hazard. The following safety measures SHALL be in place:
- Test fixture SHALL have interlock switches that disable voltage when opened.
- Operator SHALL wear insulating gloves and stand on an insulating mat.
- Test area SHALL be clearly marked and restricted to trained personnel.
- HiPot tester SHALL have a “discharge” function to safely discharge capacitive loads after test (especially for DC testing).
- For bare boards, use guarded test fixtures to avoid surface leakage affecting measurement.
9. Sampling & Documentation
- Qualification: Test 5 panels per lot or 3 lots (initial). Run full dwell time (60s) at specified test voltage.
- Production testing (Class 3 mains‑connected): 100% of panels SHALL be tested. Test voltage may be reduced to 1,250V AC for 1‑5 seconds (per IPC‑6012E).
- For low‑volume high‑reliability: Test every panel at full voltage.
- Documentation: Supplier SHALL provide a HiPot test report including:
- Test voltage (AC/DC), ramp rate, dwell time.
- Leakage current measured (or pass/fail).
- Any arcs detected and location.
- Pass/fail decision.
10. FAQ – HiPot Testing
Q: What is the difference between HiPot and isolation resistance testing?
A: Isolation resistance uses low voltage (100‑500V DC) and measures resistance. HiPot applies high voltage (typically >1,000V) and measures leakage current, detecting breakdown and arcing that isolation resistance cannot.
Q: Should I use AC or DC HiPot for my PCB?
A: AC HiPot is required for mains‑connected products per safety standards (IEC/UL). DC HiPot is often used for high‑voltage DC circuits (automotive, industrial) because it charges the insulation capacitance without continuous charging current, making leakage measurement more stable. Both are acceptable; follow product standard.
Q: What is the typical leakage current limit for a bare PCB HiPot test?
A: For bare boards, ≤5 mA AC or ≤10 µA DC. For assembled boards with Y‑capacitors, leakage can be higher (up to 5 mA AC). Always refer to the product safety standard (e.g., IEC 60950‑1).
Q: Can HiPot testing damage good boards?
A: If performed correctly (within specified voltage and dwell time), HiPot should not damage good boards. However, repeated HiPot testing on the same board can stress insulation; limit to 3 times maximum. For sensitive components (e.g., MOVs, gas discharge tubes), disconnect them before HiPot.
HiPot Test Specification Checklist
- 1. Test method (AC or DC) and test voltage specified per operating voltage and standard.
- 2. Dwell time defined (60s for qualification, 1‑5s for production).
- 3. Leakage current limit set (≤5 mA AC or ≤10 µA DC for bare boards).
- 4. Arc detection enabled on HiPot tester.
- 5. Test points defined (between each high‑voltage net and ground, between nets of opposite polarity).
- 6. Safety interlocks and operator protection in place.
- 7. For assembled boards, components that may be damaged (e.g., varistors) disconnected.
- 8. Supplier to provide test report with pass/fail and leakage current values.
- 9. For Class 3 mains‑connected, 100% production HiPot required.
- 10. HiPot tester calibration annually; verification before each test shift.
References: IPC‑TM‑650 2.5.7 (Dielectric Withstanding Voltage), 2.5.7.1 (Conformal Coating); IPC‑6012E §3.5; IEC 60950‑1; UL 60950; IPC‑2221 (creepage/clearance). IPC‑TM‑650 Official Method.
Need HiPot testing for your PCB or power supply design? Our lab performs dielectric withstand testing per IPC‑TM‑650 2.5.7 with full safety compliance.
Request HiPot Testing →Get Custom Quote
PRODUCTS CENTER


