Microvia Structure and Manufacturing

Microvia Structure and Manufacturing

Quality & Inspection Standards

PRODUCTS CENTER

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit
Microvia Manufacturing IPC‑6018

Microvia Structure and Manufacturing

A microvia is only as reliable as its plating and fill. We have seen entire HDI board lots scrapped because of a single blind‑via bottom void that opened after reflow. This guide covers laser drilling, copper plating, fill processes, and the IPC‑6018 acceptance criteria that separate a production‑ready microvia from a latent failure.

📅 Published: May 13, 2026  |  ⏱️ 14 min read  |  🏷️ #Microvia #HDI #Plating

1. Microvia Definition & IPC‑6018 Classification

Per IPC‑6018 §4.4.1, a microvia is a blind or buried via with an aspect ratio (hole diameter to depth) ≤ 1:1, and a finished hole diameter ≤ 150 µm (6 mil). The depth is measured from the surface foil to the target pad.

Microvia Type Typical Diameter Typical Depth IPC‑6018 Reference
Blind microvia (single‑level) 75–100 µm 40–80 µm §4.4.1
Buried microvia 100–150 µm 60–150 µm §4.4.1
Stacked microvia 100–150 µm Per layer, up to 2 levels recommended §5.2 (reliability)

Table 1: Microvia classification and IPC‑6018 dimensional limits.

2. Laser Drilling Process & Via Formation

CO₂ and UV lasers are the two dominant sources. CO₂ lasers (10.6 µm wavelength) ablate dielectric efficiently but cannot drill copper directly — they require a conformal mask or a pre‑etched window on the surface copper. UV lasers (355 nm) can drill copper and dielectric in one step, enabling smaller via diameters but at lower throughput.

  • CO₂ process: copper surface foil acts as a mask; laser removes dielectric down to the inner layer copper pad. Residue (glass fibers and resin smear) must be removed by plasma or permanganate desmear per IPC‑6018 §3.2.
  • UV process: direct ablation of both copper and dielectric. Less residue but requires careful energy control to avoid copper melting at the via bottom.

Manufacturing Reality

We have seen CO₂‑drilled blind vias where incomplete desmear left a thin resin film at the via bottom. This film creates a high‑resistance contact that passes initial electrical test but opens after the first thermal cycle. IPC‑6018 §4.4.3 requires a cross‑section to verify complete removal.

3. Copper Plating & Fill Processes

After laser drilling, the via must be plated to form a continuous conductive path. The plating process faces a fundamental challenge: the blind hole geometry limits solution exchange, making it difficult to achieve uniform copper thickness from the surface to the via bottom.

3.1 Electroless Copper Seed Layer

A thin electroless copper layer (0.3–0.5 µm) is deposited first. For microvias with aspect ratios near 1:1, the seed layer at the via bottom can be thinner than the surface — a critical weak point. Per IPC‑6018 §4.4.3, the minimum copper thickness in the blind via must be ≥ 20 µm average, with no local spot below 18 µm.

3.2 Electrolytic Plating

Direct‑current (DC) plating tends to create a thicker deposit at the via rim than at the bottom — a phenomenon called “dog‑boning.” Pulse reverse plating improves throwing power, delivering more uniform thickness down the via wall. For stacked microvias, the copper‑copper interface between the lower via and the upper via cap plating is the highest‑stress region. We have observed that a thin cap layer (≤ 15 µm) fails more frequently under thermal cycling.

3.3 Via Fill

For via‑in‑pad structures, the microvia must be completely filled — typically with non‑conductive epoxy or copper paste. IPC‑6018 §4.4.3 allows a maximum void volume of 5% within the fill. Any dimple on the surface must be less than 15 µm deep, otherwise solderability and planarization are compromised.

4. Common Manufacturing Defects & Inspection

Defect Root Cause Detection Method IPC‑6018 Requirement
Bottom plating void Insufficient desmear, poor solution exchange Cross‑section, TDR §4.4.3: no voids at interface
Resin smear / glass protrusion Incomplete laser ablation or desmear Cross‑section, SEM §3.2: clean via bottom required
Thin copper at via knee DC plating throwing power limit Cross‑section, X‑ray §4.4.3: 20 µm average, 18 µm local
Fill void / dimple Air entrapment, insufficient fill pressure X‑ray, optical inspection §4.4.3: void ≤ 5% volume

Table 2: The four most common microvia defects and their IPC‑6018 acceptance criteria.

5. Design Rules for Reliable Microvias

The following rules are derived from field experience and IPC‑6018 qualification data.

  • Target pad diameter ≥ 1.5× finished hole size for inner‑layer capture pads. This ensures annular ring ≥ 0.05 mm even with registration tolerance.
  • Keep aspect ratio ≤ 0.8:1 for production reliability, even though IPC‑6018 allows 1:1. The plating process window narrows significantly at the limit.
  • Specify pulse reverse plating for aspect ratios above 0.7:1 to avoid bottom‑thin copper.
  • Limit stacked microvia levels to 2 unless thermal cycling validation per IPC‑TM‑650 demonstrates survival beyond the required cycles for your product class.

Design Rule

When using CO₂ laser drilling, the surface copper opening must be ≥ 50 µm larger than the target via diameter to ensure clean dielectric removal. A smaller window leads to under‑drilling and glass protrusion into the via — a rejectable condition per IPC‑6018 §3.2.

6. FAQ

Q: What is the maximum acceptable void in a filled microvia?

A: IPC‑6018 §4.4.3 limits voids to 5% of the via volume. Any void visible in a cross‑section at 200× magnification is typically cause for rejection.

Q: Can I use DC plating for a 0.8:1 aspect ratio microvia?

A: Yes, but you must verify copper thickness at the via bottom with a cross‑section. At 0.8:1, DC plating often produces only 12‑15 µm at the bottom while the surface exceeds 25 µm — violating the 18 µm minimum.

Q: How many stacked microvia levels are reliable?

A: Two levels are production‑proven. Three levels introduce a third copper‑copper interface that fails after as few as 300 thermal cycles in some material systems. We recommend validating 3‑level stacks with IPC‑TM‑650 thermal stress testing before committing to production.

Microvia Manufacturing Checklist

  1. Confirm aspect ratio ≤ 0.8:1 for production margin.
  2. Specify desmear process (plasma or permanganate) per IPC‑6018 §3.2.
  3. Require pulse reverse plating for aspect ratios above 0.7:1.
  4. Verify minimum copper thickness (20 µm avg, 18 µm local) per IPC‑6018 §4.4.3.
  5. Limit stacked microvias to 2 levels unless thermal cycling validated.
  6. Inspect via fill voids — maximum 5% void volume, dimple ≤ 15 µm.
  7. Request cross‑section on first‑article for every new microvia structure.

Need a microvia stackup review or manufacturing feasibility assessment?

Request Engineering Review →

References: IPC‑6018 §3.2, §4.4.1, §4.4.3, §5.2; IPC‑6012E §3.3; IPC‑TM‑650. IPC Online Standards.

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit