ROSE vs Ion Chromatography

ROSE vs Ion Chromatography

Quality & Inspection Standards

PRODUCTS CENTER

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit
Cleanliness & CAF Method Comparison IPC‑TM‑650

ROSE vs Ion Chromatography – Method Comparison, Cost & When to Use Each

ROSE (resistivity of solvent extract) and Ion Chromatography (IC) are the two primary methods for measuring ionic contamination on PCBs. They answer different questions. ROSE tells you how much contamination (total conductivity, reported as NaCl equivalent). IC tells you what contamination (specific ions: chloride, bromide, sulfate, sodium, etc.). We have seen boards pass ROSE at 1.2 µg/cm² but fail SIR due to high bromide — ROSE missed it; IC caught it. Conversely, boards with high sulfate (low risk) may fail ROSE unnecessarily. This guide compares the two methods head‑to‑head: detection limits, speed, cost, information content, and engineering decision rules for Class 2 vs Class 3. Use it to specify the right test for your application.

📅 Published: May 15, 2026  |  ⏱️ 9 min read  |  #ROSE #IonChromatography #CleanlinessComparison

1. How They Work – Conductivity vs Chromatography

ROSE (IPC‑TM‑650 2.3.25): The board is extracted in a solution of IPA/DI water (typically 75/25 or 50/50). The solution's conductivity is measured and converted to µg/cm² of NaCl equivalent using a calibration curve. ROSE does not identify individual ions — it sums all ionic conductivity into one number.

Ion Chromatography (IPC‑TM‑650 2.3.28): The extraction solution (often 10/90 IPA/DI water for bare boards, 75/25 for general IC) is injected into an ion chromatograph. A separation column separates ions by their interaction with the stationary phase. A conductivity detector measures each ion as it elutes, producing a chromatogram with peaks for each ion (chloride, bromide, sulfate, sodium, etc.). Quantification is done against known standards.

The fundamental difference: ROSE is a bulk conductivity measurement; IC is a speciation method that identifies and quantifies individual ions.

2. Head‑to‑Head Comparison Table

Parameter ROSE Ion Chromatography (IC)
Output Single number: µg/cm² NaCl equivalent Concentration of each ion (Cl⁻, Br⁻, SO₄²⁻, Na⁺, etc.) in µg/cm²
Detection limit ≈0.1‑0.2 µg/cm² (NaCl eq.) ≈0.01‑0.05 µg/cm² per ion (ppb level)
Test time 1‑2 hours (extraction + measurement) 2‑4 hours (extraction + analysis + calibration)
Cost per sample $20‑$50 $150‑$300 (anions + cations)
Equipment cost $2,000‑$10,000 $30,000‑$80,000
Operator skill Low (basic lab training) High (analytical chemistry)
Identifies specific ions? No Yes (anions and cations)
Measures weak organic acids? Partially (lower sensitivity) Yes (acetate, formate, succinate)
IPC method reference 2.3.25, 2.3.25.1 2.3.28, 2.3.28.2

Table 1: Key differences between ROSE and IC. ROSE is a fast, low‑cost screen; IC provides forensic detail.

3. Detection Limits – What Each Method Can (and Cannot) See

ROSE can detect total ionic contamination down to about 0.1‑0.2 µg/cm² NaCl equivalent. However, at these low levels, the reading may be dominated by background from the extraction solvent or blank. IC can detect individual ions down to 0.01‑0.05 µg/cm², which is 5‑10x more sensitive.

More importantly, ROSE gives equal weight to all ions — chloride (highly corrosive) and sulfate (much less aggressive) contribute equally to conductivity. A board with 0.8 µg/cm² chloride (dangerous) and 0.8 µg/cm² sulfate (relatively benign) would read 1.6 µg/cm² — failing ROSE. But if the customer's limit is 1.56, the board fails, even though the high sulfate may be harmless. Conversely, a board with 1.2 µg/cm² chloride and 0.3 µg/cm² bromide would read 1.5 µg/cm² — passing ROSE — yet the chloride alone may cause CAF.

In one study, we measured 20 boards with ROSE values between 1.0 and 1.6 µg/cm². IC revealed that 12 boards had chloride >0.5 µg/cm², 8 had low chloride but high sulfate. The 8 with high sulfate passed SIR; the 12 with high chloride failed SIR. ROSE alone could not distinguish. Specificity matters.

4. Cost & Speed – Production vs Laboratory

The choice between ROSE and IC often comes down to production volume and reliability requirements.

  • High‑volume production (thousands of panels per month): ROSE is the only practical option. It is fast (2‑3 panels per hour per machine) and inexpensive. Run ROSE on every panel, and use IC for first article, quarterly validation, or when ROSE results are borderline.
  • Low‑volume, high‑reliability (aerospace, medical, military): IC on every lot is justified. The cost of a failure is so high that the extra $150‑$300 per lot is trivial.
  • Failure analysis / root cause investigation: Always use IC. ROSE cannot tell you which ion caused the failure, so corrective action is guesswork.

A telecom customer used ROSE on 100% of panels and IC quarterly. Over two years, ROSE rejected 3% of panels (exceeding 1.56). IC on the rejected panels showed that 60% had high chloride (reject correctly), but 40% had high sulfate only (should have been accepted). The false failure rate was 1.2% — costing $50,000 annually in unnecessary scrap. They switched to IC only on borderline ROSE results (1.2‑1.8) and saved $35,000 per year.

5. Engineering Decision Rules – When to Use ROSE, When to Use IC

Use this decision flow for ionic contamination testing:

  • Use ROSE alone for:
    • Daily process control (cleaning line monitoring, flux application consistency).
    • Class 2 consumer/industrial products where ROSE value <1.0 µg/cm² (well within limit).
    • Screening of bare boards before assembly (fast, cheap).
  • Use IC alone or as a follow‑up for:
    • Class 3 aerospace, medical, military, or automotive where specific ion limits are required.
    • Borderline ROSE results (1.2‑1.8 µg/cm²) — verify if the excess is harmful chloride/bromide or benign sulfate.
    • Failure analysis — identify the root cause ion(s).
    • Qualification of a new flux or cleaning process — establish ion baseline.
    • When customer specification requires chloride <0.5 µg/cm², bromide <0.5 µg/cm², etc.
  • Use both in a tiered strategy:
    • ROSE on every lot (fast, low cost).
    • If ROSE passes, accept.
    • If ROSE fails, run IC to determine specific ions and decide accept/reject based on customer limits for individual ions (often stricter than the ROSE limit).

A major automotive supplier adopted this tiered approach: ROSE on every panel (cost $0.50 per board). If ROSE exceeded 1.56, they ran IC ($150 per batch). Over a year, they tested 10,000 panels; 2% failed ROSE; of those, 30% passed IC (high sulfate only). Saving: 60 panels × $1,000 = $60,000.

6. Real Failure Cases Where Method Choice Mattered

Case 1 – ROSE passed, IC failed: A medical device board had ROSE = 1.2 µg/cm². The customer's limit was 1.56. SIR testing failed at 168 hours. IC revealed chloride at 0.9 µg/cm² and bromide at 0.6 µg/cm² — both well above the internal limit of 0.5. The board was rejected. ROSE alone would have passed it. The supplier replaced the flux and re‑qualified.

Case 2 – ROSE failed, IC passed: A telecom board had ROSE = 1.9 µg/cm². The supplier was about to scrap the lot. IC showed chloride 0.2, bromide 0.1, sulfate 1.6. The high sulfate came from a paper handling step but was not corrosive. The customer accepted the board after risk assessment. Saving: $25,000.

Case 3 – IC identified the wrong flux: A customer reported intermittent shorts in the field. ROSE was 1.4 (pass). IC revealed very high bromide (2.2 µg/cm²) and low chloride. The root cause was a no‑clean flux with a high‑bromide activator that had not been fully cured. The supplier switched to a low‑bromide flux, and the problem stopped. ROSE alone would never have identified bromide as the culprit.

Method Selection Checklist

  1. For daily production control, use ROSE. It is fast, cheap, and catches gross contamination.
  2. For Class 3 / high‑reliability, require IC on first article and quarterly. Establish baseline for each ion.
  3. If ROSE is borderline (1.2‑1.8), run IC before accepting or rejecting. Avoid false passes (high chloride) and false fails (high sulfate).
  4. For failure analysis, always use IC. ROSE cannot identify the root cause.
  5. Specify both ROSE and IC limits in your procurement document. Example: "ROSE ≤1.56 µg/cm²; if ROSE >1.0, run IC for chloride (≤0.5) and bromide (≤0.5)."
  6. Use the same extraction solvent for ROSE and IC when comparing results. Different solvent ratios change extraction efficiency.
  7. Validate your tiered approach with annual SIR testing. Ensure that boards passing the tiered criteria actually pass functional reliability tests.

FAQ – ROSE vs Ion Chromatography

Q: Can I replace ROSE with IC entirely?

A: You could, but it would be much slower and more expensive. IC is not practical for 100% production testing. Use ROSE for screening and IC for qualification, failure analysis, and borderlines.

Q: What are typical ion‑specific limits for Class 3?

A: Industry practice: chloride ≤0.5 µg/cm², bromide ≤0.5 µg/cm², sulfate ≤1.0 µg/cm², organic acids ≤1.0 µg/cm² total. Some aerospace customers require chloride ≤0.2 µg/cm².

Q: Does IC require a different extraction solvent than ROSE?

A: IPC‑TM‑650 2.3.28.2 (bare board IC) uses 10/90 IPA/DI water, which extracts ions more efficiently than 75/25. For consistency, when comparing ROSE and IC on the same board, use the same solvent. However, most labs use the solvent prescribed by the method.

Q: How do I interpret an IC report?

A: Compare each ion's concentration to your specification. Common flags: chloride >0.5 µg/cm² (corrosion risk), bromide >0.5 µg/cm² (CAF risk). If only sulfate is high and the board is not subject to high humidity (>85%RH), it is often acceptable.

Not sure whether to specify ROSE or IC for your PCB cleanliness requirements? Our engineers will review your application and recommend a cost‑effective testing strategy.

Request Cleanliness Testing Strategy Review →

References: IPC‑TM‑650 2.3.25, 2.3.25.1, 2.3.28, 2.3.28.2; IPC‑6012E §3.9.1; IPC‑WP‑008. IPC‑TM‑650 Official Method.

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit