Thermal Decomposition Temperature (Td)
Quality & Inspection Standards
PRODUCTS CENTER
Get Custom Quote
PRODUCTS CENTER
PCB Thermal Decomposition Temperature (Td) – TGA Method, IPC Requirements & Material Limits
Thermal decomposition temperature (Td) is the temperature at which a laminate loses 2% or 5% of its mass due to resin degradation – it tells you how close your board is to permanent failure during extreme thermal exposure. Unlike Tg (reversible softening), Td marks irreversible chemical breakdown. We have seen RoHS‑compliant boards pass reflow but char during wave soldering because the laminate Td was only 280°C and the wave pot was set to 300°C. Per IPC‑4101, Td is a mandatory property for many high‑reliability laminate types. This guide covers TGA testing per IPC‑TM‑650 2.4.24.6, typical Td values, and how to use Td in material qualification.
Table of Contents
1. What Is Td? – Irreversible Degradation vs Tg
Thermal decomposition temperature (Td) is the temperature at which a laminate loses a defined percentage of its mass (typically 2% or 5%) when heated in an inert atmosphere (nitrogen). It marks the onset of resin backbone breakdown – carbon‑oxygen and carbon‑nitrogen bonds cleave, releasing volatile gases. This is irreversible; once decomposed, the material cannot recover.
Key distinctions from Tg:
- Tg (glass transition): Physical, reversible softening. Material hardens again when cooled.
- Td (decomposition): Chemical, irreversible breakdown. Char, delamination, and loss of mechanical properties result.
Per IPC‑4101, Td at 2% mass loss (Td(2%)) is the standard reporting metric. Some suppliers also report Td(5%) for higher‑temperature comparisons. A higher Td indicates better thermal stability – critical for lead‑free assembly (peak 260°C) and high‑temperature operating environments.
Engineering Insight
Td is the ultimate thermal limit. If your assembly process or operating temperature exceeds Td, the laminate will permanently degrade – often without visible warning until the board fails electrically.
2. TGA Test Method (IPC‑TM‑650 2.4.24.6)
IPC‑TM‑650 2.4.24.6 specifies the TGA (thermogravimetric analysis) procedure:
- Sample size: 10‑30mg of laminate (copper removed via etching), cut to fit TGA pan.
- Pre‑bake: 110°C for 24 hours to remove moisture.
- Atmosphere: Nitrogen purge (oxygen <20 ppm, dew point below ‑68°C).
- Heating rate: 10°C/min from room temperature (≤50°C) to 550°C.
- Measurement: Record mass loss as a function of temperature. Td(2%) is the temperature at which 2% of the original mass (measured at 50°C) has been lost. Td(5%) is the 5% loss point.
A typical TGA curve shows a flat plateau below 300°C (minor moisture and volatile loss), then a sharp downward slope starting around 300‑350°C as the resin decomposes. Glass fibers remain as residue (typically 60‑70% of original mass for FR‑4).
Key acceptance criteria from the method: The TGA must be calibrated with a known standard (e.g., nickel or alumel magnetic transition). The gas flow rate must be the same during calibration and testing – changes in flow can shift Td by ±10°C.
In our lab, we have seen significant Td variations caused by poor nitrogen purity (oxygen >100 ppm accelerates decomposition, lowering Td by 15‑20°C). Always request the raw TGA curves, not just the reported numbers.
3. Typical Td Values by Material Family
The table below shows typical Td(2%) and Td(5%) ranges for common laminate systems (data from industry‑published datasheets). Always verify with your supplier.
| Material Family | Td(2%) (°C) | Td(5%) (°C) | Typical Application |
|---|---|---|---|
| Standard FR‑4 (low Tg) | 300‑320 | 320‑340 | Consumer, leaded assembly |
| Mid‑Tg FR‑4 (lead‑free capable) | 320‑340 | 340‑360 | Telecom, industrial |
| High‑Tg FR‑4 (lead‑free optimized) | 340‑360 | 360‑390 | Server, automotive, HDI |
| High‑Tg with phosphorus / halogen‑free | 330‑350 | 350‑380 | Green / halogen‑free |
| BT / Cyanate ester | 370‑400 | 400‑420 | Aerospace, high‑temperature |
| Polyimide | 430‑480 | 460‑520 | Extreme high temperature |
Table 1: Typical Td ranges. Halogen‑free materials often have slightly lower Td due to phosphorus additives. Always require Td(2%) ≥325°C for lead‑free Class 3.
In one automotive program, the supplier substituted a halogen‑free laminate with Td(2%) of 310°C. The board passed reflow but charred during wave soldering (290°C pot temperature). After we raised the minimum Td requirement to 340°C, the charring stopped. The cost increase was 8% – negligible compared to field recall risk.
4. Why Td Matters – Reflow, Wave Solder & High‑Temp Applications
Td directly impacts the board's ability to survive assembly and operation. Three critical scenarios:
- Lead‑free reflow (peak 245‑260°C): A Td(2%) >300°C is generally safe. However, if the board undergoes multiple reflows, the cumulative thermal exposure can approach Td. We have seen boards with Td 310°C survive three reflows, but fail on the fourth with visible charring around PTHs.
- Wave soldering (peak 280‑300°C): Requires Td(2%) >330°C. Low‑Td laminates will brown, blister, or char at the wave nozzle. This is especially critical for thick boards (>2.4mm) that require higher wave temperatures.
- High‑temperature operation (e.g., automotive under‑hood, power electronics): If the operating temperature is 150°C, you need a Td margin of at least 150‑200°C – the degradation rate doubles every 10°C (Arrhenius relationship). Td 340°C gives 190°C of margin, suitable for 20+ years at 150°C.
Real‑world case: A power supply manufacturer used a laminate with Td(2%) of 280°C in a 200°C ambient design. After six months, the boards became brittle and cracked. TGA analysis showed 8% mass loss – the resin had decomposed. Switching to a polyimide with Td 450°C eliminated failures. The lesson: Td must exceed operating temperature plus a degradation margin.
5. Td vs Tg – Critical Differences
Engineers often confuse Tg and Td. The table below highlights the key differences:
| Property | Tg | Td |
|---|---|---|
| What it measures | Glass‑rubber transition (physical) | Onset of chemical decomposition |
| Reversible? | Yes (cooling restores rigidity) | No – permanent damage |
| Typical range (FR‑4) | 130‑180°C | 300‑360°C |
| Test method | DSC or TMA | TGA |
| Affected by moisture? | Yes (plasticization lowers Tg) | Minimal (moisture evaporates before decomposition) |
| Primary failure mode | Excessive Z‑axis expansion, PTH cracks | Charring, brittleness, loss of insulation |
Table 2: Tg vs Td – they are not interchangeable. A high Tg does not guarantee a high Td, and vice versa.
We have seen materials with Tg 180°C but Td only 300°C – the board softened (high Tg) but still decomposed near wave solder temperature. Always specify both properties.
Td Specification Checklist (IPC‑Anchored)
- Specify Td(2%) minimum. For lead‑free assembly: ≥325°C. For wave soldering: ≥340°C. For halogen‑free: ≥320°C (typical).
- Require the test method. "Td measured by TGA per IPC‑TM‑650 2.4.24.6, 10°C/min ramp, nitrogen atmosphere, 2% mass loss."
- Request raw TGA curves. Not just the reported Td number – examine the slope and any steps that indicate multiple decomposition phases.
- Verify pre‑bake conditions. Moisture can cause a false mass loss at low temperature, shifting Td. Supplier must pre‑bake per the method (110°C, 24h).
- For high‑temperature applications, specify Td(5%) as well. Some materials show a slow initial decomposition (2% loss early) but remain stable to much higher temperatures (5% loss).
- If Td is borderline, run post‑assembly TGA on a sacrificial board. This verifies that the assembly process did not degrade the laminate.
- Document Td in your material qualification report. Include the TGA curves and the calculated Td(2%) and Td(5%).
6. FAQ
Q: What is the difference between Td(2%) and Td(5%)?
A: Td(2%) is the temperature at which the laminate has lost 2% of its initial mass – typically the onset of detectable decomposition. Td(5%) represents more advanced degradation. IPC‑4101 primarily specifies Td(2%), but for very high‑temperature applications, Td(5%) gives a better safety margin.
Q: Can a board with low Td be used if the assembly temperature is below Td?
A: Not always. Decomposition is a rate process – even at temperatures 50°C below Td, measurable degradation can occur over long exposures (e.g., 24 hours at 250°C may cause 1‑2% mass loss). For high‑temperature operation, you need Td > operating temperature + 150°C minimum.
Q: Does IPC‑6012E require a specific Td for Class 3?
A: No. IPC‑6012E references IPC‑4101 for laminate properties. IPC‑4101 defines minimum Td for each slash sheet. For example, /126 (high‑Tg FR‑4) typically requires Td(2%) ≥325°C. Always check the specific slash sheet in your procurement document.
Q: How does halogen‑free chemistry affect Td?
A: Halogen‑free laminates use phosphorus‑based flame retardants. These often decompose at lower temperatures (300‑330°C) than brominated systems (340‑360°C). However, many halogen‑free materials have been optimized to achieve Td(2%) ≥340°C. Verify with the supplier's datasheet.
Continue Reading – Thermal Reliability Series
Need help selecting a laminate with the right Td for your high‑temperature application? Our engineers will review your assembly profile and recommend materials per IPC‑4101 and IPC‑6012.
Request Material Thermal Analysis →References: IPC‑TM‑650 2.4.24.6 (TGA method); IPC‑4101 (laminate specification); IPC‑6012E; ASTM D3850. IPC‑TM‑650 Official Method.
Get Custom Quote
PRODUCTS CENTER


