Copper Core PCB Capabilities

Copper Core PCB Capabilities

Copper Core PCB Manufacturing Capabilities

 

 

 

Scope & Use Cases
Production-grade copper core PCBs (MCPCB—copper base) for high-power density, tight thermal budgets, and low thermal resistance from device-to-core. Compared with aluminum, copper provides much higher thermal conductivity (≈ 385–401 W/m·K vs. ~160–220 W/m·K), enabling faster heat spreading and lower junction temperatures in compact layouts. Typical use cases: power LED engines, laser drivers, RF PA, motor drivers/inverters, VRM/PDN hot spots, and ruggedized electronics. 

 

 

 

Parameters (Mass-Production Window)

 

Item

Capability

Notes

Stackup Types

Copper core (solid plate), copper coin/inlay, copper slug/embedded block

Localized or full-area heat paths.

Panel / Board Size

~1200 × 540 mm 

Exact max by design & line; confirm at DFM.

Board Thickness

0.5–3.0 mm 

Thicker cores for stiffness/heat; weight trade-off.

Copper Core (C1100/Cu-ETP)

1.0–3.0 mm 

Core material k≈ 385–401 W/m·K.

Circuit Copper Foil

1–4 oz 

For high current planes.

Dielectric Layer

~0.003″–0.006″ (≈ 76–152 µm)

Thinner dielectric → lower thermal resistance.

Dielectric Thermal Conductivity

~1–5 W/m·K (TIM/insulator)

Depends on MCPCB dielectric chemistry.

Min. Line / Space

0.10/0.10 mm 

Finer features possible—DFM-dependent.

Via Options

Thermal vias, plated through, VIP (resin/copper fill)

Combine with copper core or coin for hotspot relief.

Flatness (Warp/Weave)

Tight by fixturing; design for CTE + mass

Heavier copper plate improves flatness but adds weight.

Solder Mask & Finish

RFQ-specific windows; keep-out over hot pads

Mask clearance affects thermal spreading.

 

 

 

Process Routes

  • Solid Copper Core (One-piece plate): Circuit copper + thin dielectric laminated to a solid copper base for global heat spreading and mechanical stiffness. Best for entire module heat removal and shock/vibration robustness. 
  • Copper Coin / Copper Inlay: A solid copper coin or slug embedded directly beneath hot devices to create a vertical, low-θ path from pad to coin to core/ambient. Delivers superior local cooling vs. via farms or standard dielectrics.
  • Copper Block / Embedded Bar: Oversized inlay for both thermal + high-current routing, acting as a structural heat spreader and current bus. 

 

 

 

Design & Thermal Notes

  • Thermal Path Engineering. Shorten the path from device pad → dielectric → copper mass; keep dielectric as thin as safely possible (≈ 0.003–0.006″); use high-k dielectrics where insulation constraints allow. 
  • Copper vs. Aluminum. Copper’s k (≈ 400 W/m·K) provides substantially faster heat spreading than aluminum (≈ 160–220 W/m·K), at the cost of mass and price—use coins/inlays where localized performance justifies it. 
  • Combine with Thermal Vias. Under less accessible pads, via farms still help—use filled VIP beneath components to tie surface copper to internal planes or to a coin edge.
  • RF & Power Integrity. Coins/inlays can serve as low-inductance grounds and current shunts; define keep-outs and mask relief to prevent solder voids and tilt. 

 

 

 

Surface Finishes

ENIG / ENEPIG / Immersion Silver / OSP / Selective hard gold. Choose per wire-bonding, corrosion, and contact wear requirements.

 

 

 

Quality & Standards

Manufactured and qualified to IPC-6012 (rigid board performance & qualification). Use IPC-A-600 for acceptance inspection and IPC-2221 for generic design rules (creepage/clearance). 

 

 

Get Custom Quote

PRODUCTS CENTER

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit