Advanced PCB & PCBA Product Center
Explore RF, microwave, high-frequency, high-speed, HDI, rigid-flex, flexible, Rogers, heavy copper and multilayer PCB products, supported by assembly and sourcing from prototype through production.
2–128 Layer PCB Capability
RF, Microwave, High-Speed & HDI
IPC Class 2 & Class 3 Build Support
AOI, Electrical Test & Final Inspection
Explore PCB Products & Services
Showing all results
Showing of results
Rogers RO4350B High-Frequency Laminate PCB Manufacturing
Material: Hydrocarbon Ceramic · Dk 3.48 Loss: Df 0.0037 @10GHz Use: PA · Antenna · Radar
Structures: Hairpin · Coupled-Line Functions: BPF · BSF · LPF · HPF Support: Gap Control · DFM · RF Test
Subsystems: Antenna · BUC · LNB Integration: Tx/Rx · Modem · Control Support: Low-Loss · Thermal · NPI
FPV RF PCB manufacturing for FPV video transmitters, receiver modules, antenna interface circuits and low-latency video link systems. Controlled impedance, low-loss RF routing, thermal control, RF shielding and compact assembly support.
SATCOM RF PCB manufacturing for satellite communication terminals, ground stations, RF converter modules, antenna interface circuits and low-loss microwave signal paths. Rogers, PTFE, hybrid stackups, controlled impedance, RF grounding, shielding and assembly support.
Structures: Patch · Slot · Phased Array Products: Array · Tile · Feed Network Support: Material · Geometry · NPI
Use: Telemetry / GNSS / Video Link Mat: FR-4 / Rogers Focus: RF / Weight / Vibration
• Material: Rogers RO4350B + RO4450F • Layers: 6L • Key Tech: 49Ω Impedance Control
6-Layer RO4350B Controlled-Impedance RF PCB — Wideband RF Routing (5G RF Front-End, Filters)
• Material: RO4350B • Layers: 6L • Impedance: ±10%
Featured PCB & PCBA Case Studies
16-Layer Any-Layer HDI PCB
A 16-layer Any-Layer HDI architecture used stacked microvias and fine-line routing to reduce board area by 30% for a compact implantable medical device.
Read Case Study
40% Better Cooling for 800V EV Power Modules with Embedded Copper & Heavy Copper
Overheating threatened reliability. We embedded copper busbars and applied selective heavy copper—transforming the PCB into an active power path, cutting peak temperature by 40% for safe continuous operation.
Read Case Study
24/7 Reliability for Smart City Surveillance with High‑Tg & Blind/Buried Via
Intermittent failures after thermal cycling? We used high‑Tg/low‑CTE materials, blind/buried vias, and thick gold plating—eliminating via fatigue for continuous outdoor operation.
Read Case Study
Copper Inlay & Hybrid Lamination for High‑Power Robotics Thermal Management
A 120A servo drive overheated under continuous load. We embedded copper inlays for direct heat paths and used hybrid lamination to separate power from signal—achieving stable operation without bulky cooling.
Read Case Study
Solving Rigid‑Flex Failure in High‑Vibration Aerospace Systems
Intermittent signal drops and thermal cycling failures traced to rigid‑flex transitions. We smoothed the transition, rebalanced the 14‑layer stack‑up, and tightened process controls—eliminating failure under vibration.
Read Case Study
224Gbps AI Server PCB: From Signal Collapse to Stable Channel
Closed eye diagram and excessive loss at 224Gbps? We redesigned the channel, switched to Megtron 7, and applied sub‑8mil backdrilling—recovering a clean eye diagram and stable transmission.
Read Case Study
PCB Product Selection & Quotation FAQ
What files are needed to quote a microwave PCB with controlled impedance?
Gerber/ODB++, target impedance list, stack-up intent (or constraints), coupon requirements, and any critical RF routing notes.
Do you support “thin copper” or local copper optimization for sharper RF corners?
It can be supported when the design requires it; local thin-copper processing may improve corner accuracy versus full-board copper tolerance control.
Do you have real RF performance validation data?
Yes. The microwave filter bandwidth target is 5.7–7.0GHz; measured test is 5.86–7.19GHz, matching within <5% deviation.
What impedance tolerance can you support for this build?
This design targets ±5% impedance tolerance with verification and process locking for consistency.
Why use resin-filled vias on high-frequency microwave boards?
Resin-filled vias improve surface planarity and reduce solder wicking/void-related risk, supporting reliable RF assembly.
Our Manufacturing Capabilities
Core PCB and PCBA technologies supporting RF, high-speed, HDI, flex, power electronics and complex multilayer projects.
Submit Your PCB or PCBA Project for Engineering Review
Upload your Gerber or ODB++, fabrication drawing, stackup, BOM and project requirements. Our engineering team will review the manufacturing scope, technical risks and quotation requirements.
World-class PCB & PCBA manufacturer focused on high-frequency and high-reliability boards for defense, aerospace, automotive and industrial electronics.
You can unsubscribe at any time with a single click.
Copyright © 2025 UltroNiu Electronics Group All Rights reserved.