2-Layer RO4350B High-Frequency RF PCB
For RF communication infrastructure, radar modules, satellite links, and high-speed digital RF systems.
Material/Stack-up: Rogers RO4350B, TG280 high-Tg laminate
Layers + Thickness: 2L, 0.65 mm finished thickness
Impedance Control:±10% (target-dependent) + verification available
Key Process: Resin Plugged / Resin-Filled Vias
Verification/Test: 100% continuity + impedance verification
Introduction
This 2-layer high-frequency RF PCB is engineered for stable signal transmission in demanding RF applications. Built on Rogers RO4350B low-loss laminate (TG280), it integrates resin-filled vias and controlled impedance design to improve impedance repeatability, surface planarity, and long-term assembly reliability.
- Low-loss laminate (RO4350B, TG280): stable dielectric behavior for RF routing
- Controlled impedance (±10%): target-dependent control with verification available
- Resin-filled vias: better planarity, reduced solder wicking, improved SMT reliability
- ENIG surface finish: consistent solderability and stable surface performance
- Process control: optimized plating + solder mask definition for manufacturing consistency

Technical Specifications
Item | Specification | Item | Specification |
Layers | 2 | Maximum board size | 90.7 × 147.7 mm |
Material | High Frequency, Tg280, Rogers RO4350B | Surface Finish | ENIG (Immersion Gold) |
Board Thickness | 0.65 mm | Blind/Buried Vias | / |
Copper Thickness | 1 oz | Controlled Impedance | Yes (±10%, target-dependent) |
Min. Hole Size | 0.25 mm | Via Process | Resin Plugged / Resin-Filled Vias |
Min. Line / Space | 6/8 mil | Electrical Test | 100% Continuity / Impedance Verification |
Aspect Ratio | 3:1 | Certifications | ISO 9001, ISO 13485, UL 94V-0, RoHS, IPC-6012B Class III |

Engineering Trade-offs & Performance Optimization
Engineering Balance Between RF Performance and Process Capability in 2-Layer PCB Fabrication: while the structure is simple, achieving stable impedance and reliable SMT performance requires tight control of line geometry, solder mask definition, and resin filling quality.
Design Lever | Trade-off | Engineering Impact |
Laminate selection (RO4350B) | Cost vs. Dk stability | Stable dielectric behavior enables predictable RF loss and impedance, at higher material cost. |
Target impedance (±10%) | Impedance accuracy vs. etch tolerance | Tight width control and etch compensation are required to keep impedance within the target window. |
Resin-filled vias | Planarity vs. cycle time | Improves SMT planarity and prevents solder wicking, but requires void-free filling control. |
Solder mask definition | Electrical isolation vs. process limit | Fine solder mask features need high-resolution LPI control to avoid bridge defects and assembly shorts. |
Optimization highlights:
- Material-centric impedance modeling using RO4350B dielectric behavior and manufacturing etch factor
- Controlled solder mask thickness/consistency as part of the final impedance environment
- Void-free resin filling + planarization sequence to improve assembly yield
- In-process SPC to stabilize plating and overall geometry consistency

DFM Improvement Cases
Real RF yield is protected by manufacturability decisions. Below are typical DFM improvements applied to protect impedance stability and SMT reliability.
- Case 1 – Solder mask dam robustness at minimum spacing: Implemented controlled pad-size reduction (e.g., ~0.1 mil per side) to ensure a reliable solder mask bridge and reduce solder bridging risk.
- Case 2 – Stack-up feasibility alignment: Adopted a manufacturable RO4350B core option to ensure stable supply and consistent thickness control, with negligible RF performance impact.
- Case 3 – Impedance scatter reduction: Fine-tuned trace geometry and validated with impedance verification to reduce scatter and support the target tolerance window.
Application Scenarios

5G Base Stations / Telecom Infrastructure:
Low-loss routing and controlled impedance for RF signal chains and matching networks.
Microwave Transmission Equipment:
Stable dielectric behavior supports consistent insertion loss and impedance repeatability.
Satellite Communications:
Predictable RF performance with controlled impedance structures.
RF Power Amplifiers / RF Front-End Modules:
ENIG finish + resin-filled vias improve assembly reliability for high-density RF layouts.
Radar & High-Reliability RF Systems:
High-Tg laminate helps thermal endurance in demanding environments.
High-Speed Digital RF Systems:
Controlled impedance and stable manufacturing consistency for mixed-signal boards.
Related Products
Related Products
12-Layer 4oz Heavy Copper PCB
12L FR-4 · Shengyi S1000-2M 4oz Inner Copper (L4–L7) 2.54 mm Finished · Immersion Tin
8-Layer 3oz High-Tg Heavy Copper PCB
8L FR-4 · Shengyi S1000-2M 3oz Inner Copper · Tg170 2.0 mm Finished · ENIG
6-Layer 3oz Heavy Copper PCB with Edge Plating
6L FR-4 · Shengyi S1000H 3oz Copper · Edge Plating Edge Metallization · Copper Clearance
4-Layer 3oz Heavy Copper PCB
4L FR-4 · Plated Through-Holes 3oz Inner · Approx. 3oz Finished Outer Copper Build · Etching · Plating DFM
4-Layer Multi-Connector Rigid-Flex PCB with PI Flex Core
Structure: 4L Rigid · 2L PI Flex (L2/L3) Layout: Multi-Branch Connector Interfaces Engineering: Copper-Balance & Transition DFM
8-Layer Panelized Rigid-Flex PCB for Multi-Connector Modules
Structure: 8L Rigid · 2L PI Flex (L4/L5) Configuration: Repeated Connector Array Engineering: Panel Rails · Transition DFM
10-Layer Rigid-Flex PCB with Resin-Plugged Vias
Structure: 10L Rigid · 2L PI Flex Core Via Process: Mechanical PTH · Resin Plugging Engineering: Connector DFM · Regional Stackup
8-Layer Rigid-Flex PCB with Dual PI Flex Cores
Structure: 8L Rigid · Dual PI Flex Cores Flex Layers: L2/L3 + L6/L7 Features: Multi-Region Routing · ENIG
10-Layer 2nd-Order HDI Rigid-Flex PCB with Laser Microvias
Structure: 10L Rigid-Flex · Dual PI Flex Cores HDI: 2nd-Order · 4 mil Laser Microvias Technology: Fine-Pitch Routing · Resin-Plugged Vias
6-Layer Multi-Zone Rigid-Flex PCB with Dual PI Flex Cores
Structure: 6L Rigid · Dual PI Flex Cores Routing: Multi-Zone · L2–L5 Flex Layers Focus: Dense I/O · Stackup DFM
FAQ
When should I consider Rogers materials instead of standard FR-4?
There is no single frequency threshold for every design. Rogers materials should be considered when insertion loss, dielectric stability, phase consistency, thermal behavior or long transmission paths begin to limit system performance. Operating frequency, bandwidth, path length, copper profile and loss budget should be evaluated together.
Can you recommend a specific Rogers laminate for my project?
Yes. Material selection is reviewed against operating frequency, insertion-loss budget, Dk/Df, copper profile, thermal requirements, layer construction, availability and cost. Common options include RO4350B, RO4003C, RO3003 and RT/duroid 5880, but the final recommendation depends on the complete stackup and application requirements.
Can Rogers and FR-4 be used in the same PCB?
Yes. Rogers + FR-4 hybrid stackups can place low-loss laminates on critical RF or microwave layers while using FR-4 for digital, control or power sections. Material compatibility, CTE behavior, bondply selection, resin flow, dielectric thickness, copper balance and lamination cycles must be reviewed before fabrication.
What is the difference between RO4350B, RO4003C, RO3003 and RT/duroid 5880?
RO4350B and RO4003C are widely used hydrocarbon-ceramic laminates that offer a practical balance of RF performance and manufacturability. RO3003 provides lower loss and stable dielectric properties for microwave and mmWave applications. RT/duroid 5880 is a PTFE-based ultra-low-loss material often selected for demanding antenna, radar and SATCOM designs. Final selection should also consider copper profile, thickness, processing and cost.
When should a design be reviewed as a microwave PCB manufacturing project?
A PCB should be reviewed as a microwave PCB manufacturing project when operating frequency, wavelength, insertion loss, return loss, phase behavior or discontinuities begin to affect system performance. Multi-GHz radar, SATCOM, phased-array, RF test and selected mmWave applications usually require microwave-specific material, stackup and fabrication controls.
Project Launch CTA
Upload your files and receive a free DFM review and quote within 12 hours. We ensure all data is kept strictly confidential under NDA.


