50A 6S 4-in-1 ESC
50A 6S 4-in-1 ESC
50A 6S 4-in-1 ESC
50A 6S 4-in-1 ESC
+
  • 50A 6S 4-in-1 ESC
  • 50A 6S 4-in-1 ESC
  • 50A 6S 4-in-1 ESC
  • 50A 6S 4-in-1 ESC

50A 6S 4-in-1 ESC

50A 6S 4-in-1 ESC with 55A peak current, 2–6S LiPo input, a 64 × 45 mm board and 34.4 mm mounting. Four motor connectors, PWM/DShot control and OEM supply support.

UESC-50-6S-4I-A is a 50A 6S 4-in-1 ESC for FPV and UAV development teams that need four motor outputs, a connector-based board layout and defined flight-controller signal mapping. Rated at 50A continuous and 55A peak current with 2–6S LiPo input, it combines a 64 × 45 mm outline, 34.4 × 34.4 mm mounting pattern and a six-layer, 3oz copper PCB. UltroNiu supports OEM product sourcing and custom PCB/PCBA programs for compatible UAV electronics.

50AContinuous current
55APeak current
2–6SLiPo input
4-in-1Motor channels
34.4 mmMounting-hole spacing
6L / 3ozHeavy-copper PCB
01 / Product overview & design fit

Four-channel ESC with connector-based motor integration

The UESC-50-6S-4I-A brings four brushless motor-control channels onto a rectangular 64 × 45 mm board. Four visible three-contact motor connectors, dedicated battery connection pads and an eight-position flight-controller interface provide distinct connection points for UAV electrical integration.

Built around installation requirements

The 34.4 × 34.4 mm mounting-hole pattern provides a defined mechanical reference for stack planning. Before selecting a motor and battery combination, evaluate connector ratings, harness routing, load demand and available cooling within the aircraft.

Four motor outputsDefined 8-position FC interface2–6S power system

Review the flight-controller pinout · Request a quotation

UESC-50-6S-4I-A four-in-one ESC with four yellow motor connectors in angled view
50A 6S 4-in-1 ESC · connector and board layout

Integrated motor connections

Four distinct motor output connectors help organize the four-motor wiring layout.

Defined FC signal mapping

CUR, NC, M4–M1, BAT and GND are provided as the specified eight-position interface functions.

Six-layer power PCB

3oz copper construction supports high-current routing and heat-spreading design considerations.

02 / Technical specifications

UESC-50-6S-4I-A technical specifications

Parameter Specification
Model UESC-50-6S-4I-A
Product type 4-in-1 electronic speed controller; four motor channels
Reference configuration EF60 50A
Battery input 2–6S LiPo
Rated continuous current 50A
Rated peak current 55A
Board dimensions 64 × 45 mm
Mounting-hole spacing 34.4 × 34.4 mm
Net weight 27.5 g
PCB construction 6 layers / 3oz copper
Main controller EFM8BB51F16G
Gate driver DRV8300D
Power MOSFET voltage class 30V
Voltage regulation Industrial-grade LDO
Input filtering Murata capacitors
Firmware reference E_X_40 · Rev. 16.7
Current ratio setting 120
Control protocols PWM, OneShot125, OneShot42, Multishot, DShot150, DShot300, DShot600
Motor-control functions Hardware PWM, Damped Light, active freewheeling

Current ratings are the published product specification; load capability in an aircraft depends on motor demand, harness design, airflow and installation conditions.

03 / Flight-controller & motor interface

Defined eight-position FC interface and four motor connectors

The flight-controller interface is specified in the following functional order. It separates current sensing, four individual motor commands and battery-voltage monitoring from the ground reference.

# Signal Function
1 CUR Current-sense signal
2 NC Not connected
3 M4 Motor 4 control input
4 M3 Motor 3 control input
5 M2 Motor 2 control input
6 M1 Motor 1 control input
7 BAT Battery-voltage sense
8 GND Ground
50A 6S four-in-one ESC dimensions 64 by 45 millimeters and flight-controller eight-position signal diagram
64 × 45 mm board and FC signal reference
Electrical integration: Confirm the mating connector orientation, pin-one position, signal levels and harness mapping against the selected flight controller before applying battery power. The NC position is not assigned a control function.
04 / Mechanical integration

34.4 mm mounting pattern in a 64 × 45 mm board

Airframe fit and connector clearance

The board measures 64 × 45 mm with 34.4 × 34.4 mm mounting-hole spacing. The elongated outline, four motor connectors and side-mounted flight-controller connector should be assessed together with stack height, cable bend radius and service access.

Mounting compatibility depends on the aircraft hardware and installed harness, rather than hole spacing alone.

Share your airframe and harness requirements.

50A 6S four-in-one ESC held in a gloved hand with four motor connectors visible
Product scale and connector arrangement
05 / Power electronics

30V MOSFETs, gate drive and input filtering

Power switching

30V-class MOSFETs form the motor switching stage. Battery-input transients and thermal conditions must be considered alongside the 2–6S LiPo specification.

DRV8300D gate driver

The specified driver IC provides gate-drive functions for the brushless motor power stage.

LDO and input capacitors

Industrial-grade LDO regulation and Murata capacitors support control-circuit power conditioning and supply filtering.

For 6S integration: Cable inductance, braking transients and the selected input-capacitor arrangement can affect voltage stress on the power stage. Assess the complete supply path rather than MOSFET voltage rating alone.
06 / PCB & thermal architecture

Six-layer, 3oz copper construction for four-channel power routing

The six-layer PCB uses 3oz copper construction to support power distribution between the battery input and four motor stages. Copper geometry, solder connections and component placement all affect electrical losses and heat spreading.

Thermal design is a system consideration

Continuous motor demand, mounting clearance, nearby electronics and airflow should be considered when selecting an ESC for a 6S UAV. The 50A/55A ratings should be reviewed in the context of the intended load profile.

Front view of UESC-50-6S-4I-A showing power pads, control section and four motor connectors
Power routing and connector distribution
07 / Motor-control protocols

EFM8BB51 control with PWM, OneShot, Multishot and DShot

The EFM8BB51F16G control platform uses the E_X_40 Rev. 16.7 firmware reference. The specified throttle command set covers PWM, OneShot125, OneShot42, Multishot and digital DShot150/300/600.

Damped Light motor braking

Damped Light braking and active freewheeling are listed motor-control functions. Their operating behavior depends on the firmware and controller settings used in the aircraft.

Confirm firmware target, signal mapping and motor direction as part of ESC/flight-controller setup.

Representative flight controller and electronic speed controller bench integration setup
ESC and flight-controller integration setup
08 / Application fit

A 6S four-motor ESC for UAV integration programs

FPV aircraft integration

Evaluate motor current demand, 2–6S battery configuration and connector clearances for a four-motor platform.

UAV electronics development

Use the known board outline, mounting pattern and FC signal order when assessing mechanical and electrical compatibility.

OEM controller assemblies

Coordinate ESC selection with harness specifications, component availability and project-defined acceptance criteria.

09 / PCB fabrication

PCB manufacturing for multilayer ESC power electronics

UltroNiu supports multilayer PCB fabrication for power electronics, including CAM data preparation, imaging, copper processing, solder-mask definition and bare-board electrical inspection. Project manufacturing requirements are defined from the approved PCB design data.

10 / PCBA & verification

ESC assembly planning, inspection and electrical checks

Assembly built to approved production data

For OEM PCB/PCBA projects, component sourcing, SMT assembly, high-current joints and process inspection can be scoped against approved manufacturing files, BOM and assembly drawings.

Verification matched to the application

Quality planning can include PCB electrical testing, assembly inspection, power-on checks, motor-control behavior and load criteria defined for the specific project configuration.

Panel of populated ESC-type printed circuit board assemblies
PCBA panel assembly example
Flying-probe electrical test machine for bare printed circuit boards
Bare-board electrical test
Back-side view of panelized high-current ESC-style bare printed circuit boards
Power electronics PCB panel details
11 / OEM & procurement

50A ESC sourcing and custom PCB/PCBA support

Standard ESC inquiry

Discuss the 50A 6S four-channel product, expected order volume, required accessories and delivery requirements.

Harness and controller fit

Review the flight-controller pinout, mounting location, motor connectors and cable-routing constraints.

Custom electronics projects

For separate OEM hardware designs, coordinate PCB fabrication, component assembly, BOM controls and project-specific test requirements.

To accelerate engineering review, send your battery configuration, motor and propeller combination, flight-controller model, target quantity and mechanical drawings where available.

Start an engineering review

12 / Frequently asked questions

Questions from FPV, UAV and OEM engineering teams

What battery configurations does the 50A 6S ESC support?

The UESC-50-6S-4I-A is specified for 2–6S LiPo input. Check wiring, transient behavior and cooling for the target aircraft.

What are the continuous and peak current ratings?

The published ratings are 50A continuous and 55A peak. Operating suitability depends on motor load, wiring, cooling and the installation.

What are the PCB dimensions and mounting-hole spacing?

The board outline is 64 × 45 mm, with a 34.4 × 34.4 mm mounting-hole pattern. Account for connector clearance and harness routing when planning the stack.

What is the flight-controller pinout?

The specified eight-position functional order is CUR, NC, M4, M3, M2, M1, BAT and GND. Confirm the mating-connector orientation against the intended harness.

How many motors can this ESC control?

It is a four-channel ESC intended to control four brushless motors. The board provides four visible motor output connectors.

Which throttle protocols are supported?

The listed protocols are PWM, OneShot125, OneShot42, Multishot, DShot150, DShot300 and DShot600.

Which PCB construction and control components are specified?

The listed construction is six PCB layers with 3oz copper, an EFM8BB51F16G MCU and a DRV8300D gate driver.

Can UltroNiu support OEM sourcing and custom PCB/PCBA projects?

Yes. UltroNiu can discuss ESC product sourcing and separately defined PCB/PCBA manufacturing projects. Share the electrical, mechanical and volume requirements for an engineering review.

13 / Project inquiry

Request a 50A 6S 4-in-1 ESC quotation

Discuss your ESC procurement or OEM requirements

Share your 2–6S battery configuration, motor current needs, flight-controller interface, mounting constraints, required quantities and delivery target. For customer-specific hardware, include Gerber, BOM or drawings where available.

Request Engineering ReviewEmail the Team

Related Products

120A 12S Single ESC

Single-motor 6–12S ESC rated 120A continuous / 140A peak, with 55 × 32 mm outline, 8-layer 4oz copper PCB and PWM/DShot control support. OEM sourcing and custom PCB/PCBA services.

80A 12S 4-in-1 ESC

Four-channel 6–12S ESC with 80A continuous and 100A peak ratings, stacked control/power boards, 8-layer 4oz PCB and two mounting-hole patterns.

110A 8S 4-in-1 ESC

Four-motor ESC with 2–8S LiPo input, 110A continuous and 120A peak ratings, 56 × 52 mm outline, 8-layer 3oz copper PCB and PWM-to-DShot600 support.

Project Launch CTA

Upload your files and receive a free DFM review and quote within 12 hours. We ensure all data is kept strictly confidential under NDA.

Supported formats: PDF, DWG, Gerber, Excel (Max 50MB)
Submit