A PBGA can pass moisture/reflow classification and post-reflow electrical checks yet still be vulnerable to a different failure later in service. Leakage during humid operation and intermittent opens during temperature cycling point to different damage sites. Neither is settled by the fact that the package survived reflow.
The package combines moisture-sensitive polymer interfaces, internal metallization and solder connections. Once it is assembled on a PCB, the solder joints see board strain, while exposed conductors may see residues, moisture and electrical bias. A qualification plan has to follow those physical paths. Simply adding more hours in a chamber does not establish which one was tested.
A workable PBGA qualification plan needs separate evidence for three risks: moisture/reflow damage inside the package, corrosion or ECM under humid electrical bias, and fatigue of the solder attachment on the assembled PCB. The specimen, stress sequence, monitoring method and acceptance criterion must be chosen for each risk. A passing moisture-sensitivity classification cannot stand in for the other results. [2–6]

Define the Failure Site Before Selecting a Test
The first question is what, exactly, is being qualified. Inside the package, absorbed moisture may affect the mold compound, die attach or bonded interfaces. On the assembled PCB, solder balls see the effects of board strain and thermal-expansion mismatch; exposed conductors and process residues may also create leakage paths. In the finished product, power states, enclosure temperatures and repeated transitions determine whether those stresses occur together. A device-level result does not automatically cover the board-level attachment or the field operating sequence.
The qualification review therefore needs more than an ambient temperature and RH range. It needs the package construction and MSL, the actual reflow exposure, PCB layout and solder process, cleaning and rework history, electrical bias states and the expected temperature transitions. Condensation during power-up is a particular concern when the board surface can fall below the local dew point. That mechanism is covered separately in our article on PCB condensation and ECM.
For example, a surface-insulation-resistance coupon may reveal leakage associated with a particular board finish or flux process. It cannot, by itself, establish whether the die-to-mold-compound interface has delaminated. Conversely, a moisture/reflow qualification of the device says little about the fatigue life of its solder balls on the customer's PCB. The test vehicle must represent the suspected failure location.
What the 2026 PBGA Study Measured
Wen and colleagues approached the problem from several directions: ECM experiments using different electrode systems, hygrothermal aging of PBGA packages, and a multiphysics model. [1] These are complementary observations, not a single life test in which every specimen received the same combined sequence. Keeping the test groups distinct is essential when interpreting the numbers.
| Test object / investigation | Reported condition | Observed result | Limit of interpretation |
|---|---|---|---|
| ECM, bare copper electrodes | 10 V applied in a high-humidity experiment | Dendrite initiation at 29 s; conductive bridging at 52 s | A universal PBGA short-circuit time or allowable operating voltage |
| ECM, SAC305/OSP/Cu electrodes | 10 V applied in a high-humidity experiment | Dendrite growth at 384 s; bridging at 392 s | Direct equivalence to internal bond pads or assembled solder joints |
| PBGA hygrothermal aging | 60°C / 85% RH | Severe die/mold-compound delamination reported after 192 h, extending toward most of the interface after 1,000 h | A universal moisture-aged service-life or acceptance threshold |
| Multiphysics simulation | Coupled fields within the reported model | Model-specific peak stresses of 134.9 MPa in interconnect region and 83.8 MPa in die region | Measured PBGA stress, allowable stress or a design limit |
The publicly available method excerpts identify a 20 × 20 × 1.6 mm FR-4 coupon and electrode dimensions of 2 × 0.65 × 0.035 mm for the ECM work. They do not provide enough detail to independently establish every electrode gap, the complete temperature/RH history of each group, the full reflow profile or the sample counts and repeatability. Those limitations matter: geometry and surface condition strongly affect ECM timing, while package construction determines how hygrothermal exposure translates into damage. [1]
In particular, the reported 52 s and 392 s bridging times should not be turned into a claim that one finish provides a corresponding multiplier of field life. The experiments used different electrode systems, and the available methods are insufficient for that extrapolation. The numerical results are useful as evidence of mechanism under the reported conditions—not as product qualification limits.
Delamination and ECM Are Not the Same Failure
Moisture and reflow can damage package interfaces
Non-hermetic polymer packages absorb moisture. During reflow, rapid heating can raise vapor pressure inside the package while expansion mismatch strains the die, mold compound and substrate interfaces. Damage may appear as cracking or separation at an interface; prolonged humid aging can also change adhesion without producing an immediate electrical failure. These are structural outcomes. An ordinary continuity check may remain unaffected until damage progresses or reaches a critical interconnect. [1–3]
Evidence for this mechanism begins with the moisture exposure and the actual component-body temperature during reflow. Visual inspection and acoustic imaging may locate damage; cross-sectioning may be needed to confirm the interface involved. An acoustic indication is not automatically a rejection. The relevant package construction, its acceptance criteria and the significance of that interface change must be considered together.
Humid electrical bias can create a conductive path
ECM requires more than absorbed moisture. It needs an electrochemically active material system, an electrolyte path, sufficient electrical potential and chemistry that allows metal to dissolve, migrate and redeposit. Leakage may rise before a visible dendritic bridge is identified. Electrical data can show when insulation changed; microscopy or chemical analysis may be needed to establish what caused the change. [1, 7]
Location again matters. A dendrite on an exposed PCB test pattern is not the same failure site as corrosion beneath a package or at an internal connection. The electrode spacing, finish, residues, bias and moisture path must resemble the actual risk. The 2026 paper's copper and SAC305/OSP/Cu tests help illustrate that dependence, but their bridging times are not a countdown to PBGA failure in service.
Match the Stress Test to the Failure Mechanism
A qualification matrix is useful only if each test has a defined purpose. The table below links the likely damage site with a relevant method and the records needed to interpret the result. It is not a fixed sequence or a universal set of chamber settings. Exact conditions come from the applicable standard revision, customer requirements and the product's risk assessment.
| Stress and specimen | Potential damage | Applicable method | Evidence needed |
|---|---|---|---|
| Moisture soak + assembly reflow Package |
Popcorning, interfacial delamination or package cracking | IPC/JEDEC J-STD-020F (MSL classification); JESD22-A113J (preconditioning before reliability testing) | Correct MSL, soak and component-temperature reflow profile; pre/post structural inspection; defined damage criteria |
| Unbiased elevated humidity Package |
Moisture ingress, swelling and adhesion deterioration; moisture-assisted corrosion without applied external bias | JESD22-A118, where applicable; project-specific hygrothermal study | Temperature/RH/time log; post-stress acoustic/section assessment and electrical checks |
| Humidity + applied bias Packaged device |
Corrosion, leakage, internal electrochemical damage | JESD22-A101 (THB) or JESD22-A110 (biased HAST), where justified | Bias pin map, actual voltage and power, junction/chamber thermal state, monitored leakage/function and FA |
| Humidity + electrical bias + representative residues PCBA or coupon |
Surface insulation resistance reduction, dendrites or other ECM | IPC-TM-650 2.6.3.7 for suitable test coupons / process characterization | Documented electrode spacing, surface processing, bias, continuous resistance history and microscopy |
| Thermal cycling Packaged device / PCBA |
Package interface or interconnect fatigue; external PBGA solder-joint fatigue at board level | JESD22-A104 (device); IPC-9701B (board-level solder attachment characterization) | Actual cycle profile, dwell/ramp, representative PCB build, continuity monitoring and joint cross-section / FA as required |
| Combined or sequential service stresses Product-specific |
Interaction between latent moisture damage, bias exposure and thermal-mechanical fatigue | Risk-driven test sequence—not a standalone universal PBGA test | Sequence rationale, distinct/overlapping cohorts, baseline/post-stress states and acceptance for each mechanism |
The distinctions between these methods are important. J-STD-020F addresses moisture/reflow sensitivity classification; JESD22-A113J addresses preconditioning for subsequent reliability tests. Neither, alone, demonstrates long-term resistance to humid electrical bias. Device-level temperature cycling and board-level solder-attachment cycling also answer different questions. [2–6, 8]
Why a Standard Chamber Condition Is Not a Qualification Recipe
Supplier reliability reports sometimes cite 85°C/85% RH for 1,000 hours under bias, or 130°C/85% RH for 96 hours in biased HAST. Those conditions are familiar examples, not automatic prescriptions for every PBGA. The chosen method also governs details such as bias application, chamber operation and measurement intervals. Aggressive acceleration can change the dominant failure mechanism; a convenient test duration is not a substitute for exposure relevance.
The Wen study's 60°C/85% RH aging condition and its 10 V electrode experiments should likewise be reported separately. They do not form a verified universal “10 V at 60°C/85% RH” qualification. Temperature, humidity, voltage, specimen construction, exposure time and failure criterion belong to the same experimental record. Omitting any of them makes the result difficult to use.
Plan the Sequence So a Failure Can Be Interpreted
Freeze the tested build and its identifiers
Record the package part and construction, PCB revision, solder alloy, assembly and cleaning conditions, any rework, and the intended power states. The sample IDs should remain linked to these details throughout the study. If coupons are used, document the specific surfaces and process steps they represent. Without that link, a later leakage or delamination finding may be impossible to connect to production hardware.
Capture a baseline before applying lifetime stresses
Where required, apply the correct moisture-sensitivity handling and preconditioning flow before reliability stress. Keep the device's MSL, moisture exposure and component-body reflow profile with the test record. Establish the initial electrical and structural condition of the specimens; otherwise, damage seen after the chamber exposure may have originated earlier in assembly. Reflow temperatures and moisture soaks must follow the device and applicable method, not a single default profile. [2, 3]
Run separate stress branches when the mechanisms differ
Package moisture/reflow integrity, biased-humidity corrosion and solder-joint fatigue often need different test vehicles or cohorts. Sequential exposure is appropriate when the real product sees that order of events, but it must be planned explicitly. A specimen sectioned for failure analysis cannot continue into another test; repeated stressing can also make the eventual cause harder to isolate. Reference specimens and clearly separated stress groups help preserve the comparison.
Monitor the symptom while the stress is present
Intermittent solder-joint opens may occur only during the temperature ramp. Leakage can peak during humid bias and disappear after the board dries. A room-temperature pass at the end may miss both. The plan should specify what is monitored, the required time resolution, the voltage state and the actual chamber conditions. Structural checks before and after stress then help explain the electrical record rather than replace it.
Agree on failure criteria before reviewing the results
What counts as unacceptable delamination? How much leakage is too much? Is a brief continuity interruption a failure? The answers need to be set before testing, along with the inspection methods and disposition rules. Reports should distinguish a confirmed dendritic bridge from unexplained leakage, or observed interface separation from a proven functional failure. Retests and exceptions need named approval authority and a documented rationale.
What a Useful Qualification Report Must Show
| Evidence to retain | Question to answer | Typical record |
|---|---|---|
| Test-object identity | Was the specimen a package, assembled board or representative coupon—and which revision? | Package/BOM/board/lot/sample map |
| Environmental exposure | What temperature, RH, soak and ramp conditions did the actual specimen experience? | Chamber data and verified thermocouple profiles |
| Electrical stress | Where and when was voltage applied, and what leakage or function was monitored? | Bias pin map, power state, time-resolved records |
| Mechanical / structural condition | Was there interface separation, cracking, bond damage or solder-joint fatigue? | Appropriate acoustic imaging, X-ray, microsection and FA report |
| Acceptance and traceability | Which predefined requirement was evaluated for each specimen? | Criteria, failures/deviations, disposition and signed release |
A short “PASS” summary cannot answer these questions on its own. For HAST, the report should say whether bias was applied, at which pins and voltages, and what was monitored. For delamination, it should identify the inspected interfaces and the acceptance rule. For board-level cycling, it should show why the test board, solder alloy, reflow history and cycle profile represent the intended assembly.
What to Agree Before the NPI Build
- Environment: What temperature and humidity transitions will the assembly actually see, and can condensation occur while powered?
- Package and process: Which PBGA part, MSL, PCB pad design, reflow profile, solder material and cleaning/rework steps define the test build?
- Electrical state: Which pins are biased in storage, startup and normal operation? What potential differences exist across susceptible paths?
- Likely failure site: Is the priority an internal interface, corrosion/leakage, PCB surface condition or external solder fatigue?
- Proof of acceptance: Which specimen IDs, inspections, in-stress electrical data and failure criteria will support the release decision?
For a PCB and PCBA manufacturing partner such as UltroNiu, the practical contribution is to review how fabrication and assembly choices affect the test vehicle: board stackup, pad geometry, soldering, cleaning, rework and production traceability. Qualification of the semiconductor package itself, specialist failure analysis and component certification require separately agreed scope and evidence. Manufacturing review cannot replace the device supplier's reliability data.
The final review should be able to answer a narrow question for each mechanism: Did the tested construction experience the relevant stress, and was the expected damage actually checked? If the answer is unclear, adding another chamber exposure may produce more data without making the qualification more convincing.
Send the PCB fabrication data, PBGA part and MSL, assembly/reflow details, bias conditions and proposed test plan. Those inputs allow the PCB/PCBA manufacturing requirements to be reviewed against the risks the qualification is intended to address.
Questions Engineers Commonly Ask
Does MSL classification prove long-term PBGA reliability?
No. MSL addresses sensitivity to moisture exposure during handling and reflow. Humid-bias corrosion, package aging and fatigue of the solder attachment need their own relevant tests and endpoints. [2, 3]
Can a passing biased-HAST result rule out package delamination?
Not without structural evidence. A biased-HAST electrical pass may coexist with interface changes. The planned inspection and acceptance criteria must cover the specific interface at risk.
Is surface ECM the same as conductive anodic filament (CAF) failure?
No. Surface ECM develops along a suitable wetted conductor path; conductive anodic filament (CAF) growth occurs within susceptible PCB dielectric structures. Package-internal corrosion introduces another geometry and material system. Different specimens and failure-analysis methods are needed.
Does the 2026 paper define a universal 10 V PBGA stress level?
No. The reported 10 V condition belongs to particular electrode experiments. It is not a PBGA operating-voltage limit or a standard qualification stress. Geometry, humidity, chemistry and the actual device bias determine relevance. [1]
Engineering References
- [1] Wen, J., Wang, S., Zhang, Y., Li, L., Yu, M. and Tian, Y. (2026). Failure mechanisms of PBGA packages under coupled humidity-thermal-electrical fields: Electrochemical migration behavior and multi-physics simulation. Microelectronics Reliability, 185, 116258.
- [2] IPC/JEDEC J-STD-020F (2022): Moisture/Reflow Sensitivity Classification for Non-hermetic Surface Mount Devices.
- [3] JEDEC JESD22-A113J (2026): Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing.
- [4] JEDEC JESD22-A101: Steady-State Temperature-Humidity Bias Life Test.
- [5] JEDEC JESD22-A110: Highly Accelerated Temperature and Humidity Stress Test (HAST).
- [6] IPC-9701B (2022): Thermal Cycling Test Method for Fatigue Life Characterization of Surface Mount Attachments.
- [7] IPC-TM-650 2.6.3.7: Surface Insulation Resistance.
- [8] Texas Instruments: Reliability testing methods and their stress objectives.
- [9] SGMICRO: Published examples of temperature, humidity and bias reliability test conditions.
Tags:
Related Articles
Related Products
60GHz Radar Sensor PCB
Architectures: AoP/AiP · PCB Antenna Formats: Module · Shield · Sensor Fusion Support: HDI · X-Ray · NPI
Any-Layer HDI PCB Manufacturer | 10-Layer High Density Interconnect PCB
HDI stands for High Density Interconnector, which is a PCB manufacturing type (technology), using micro blind/buried via technology to realize a high line distribution density. It can achieve smaller dimensions, higher performance and lower costs.
AI Server PCB
Products: Motherboard · GPU · Backplane Structure: High-Layer · HDI Support: SI/PI · Backdrill
Related Products/Solutions
Quick links


